Propane - Study guides, Class notes & Summaries

Fire Inspector 2 Questions and Answers 100% Solved Fire protection engineers have established _____ PSI as a minimum required residual pressure when computing the available water for flow test results. 20psi The most common gallonage rating for horizontal shaft pumps in use today are _____ - _____ GPM. 500 - 1500 gpm A fire pump serving a standpipe system should be tested ______ weekly A fire department pumper can effectively supply around ______ feet in a high rise building depending on hyd...

Which product container is most likely to BLEVE? a. refrigerated rail road car b. open top hopper c. 5 gallon liquid propane tank d. non pressurized tank container - Answer c. 5 gallon liquid propane tank During structural fire fighting operations you should always consider a secondary ____________ route. a. response b. hose lay c. frequency d. escape - Answer d. escape How many ICS bulldozer types or classifications are there? a. 1 b. 2 c. 3 d. 4 - Answer c. 3 Do not get off the...

Notice of Accidents - Answer Immediately upon discovery of an accident that caused death or personal injury requiring professional medical treatment and that caused property damage exceeding $3000 Investigation/Safety Promotion - Answer The Department may investigate and accident involving loss of life, personal injury, or Property Damage Bulk Storage Locations - Answer 1. A single container of 2000gal or more 2. Aggregate container capacity is 4000gal or more 3. Containers serv...

To measure the strength of a welded joint what mechanical test would you prescribe? a) A transverse weld tension test. b) A charpy test. c) A CTOD test. d) An all weld metal tension test. e) A side bend test. - a) A transverse weld tension test. Select the cutting process that would provide the narrowest heat affected zone when cutting 12.5 mm (0.5 in) thick carbon steel. a) Oxy-acetylene cutting. b) Air-carbon arc cutting. c) Oxy-propane cutting. d) Plasma arc cutting. e) Laser beam...

Propane and Natural Gas Exam 2024 If an appliance cannot be converted to another fuel ex. propane to natural gas, it must be a ___ appliance - correct answer "Dedicated" Appliance The "10ft-2ft-3ft" rule is a reference to what? - correct answer It means that chimneys must be 3ft above the highest point of where it passes through, while still being 2ft higher than any portion of roof within 10ft How many feet must a type B or L vent terminate, at minimum, above the highest connecte...

CETP Pre-Certification Review QUESTIONS And Answers WITH VERIFIED SOLUTIONS GRADED A+ Propane has many advantages as a fuel source, including: - ANSWERA. It burns slowly because of its low pump-octane B. It is stationary and non-portable C. It is a clean-burning, non-toxic fuel D. It leaves a high-residue as it burns If a service technician is asked to perform a task that he or she is not fully trained or qualified for, the best action is to: - ANSWERA. Say nothing, gather up his or her...

PROPANE PRACTICE TESTS Questions with Complete Solutions

ABSA 4B EXAM QUIZ BANK | 1566 QUESTIONS | WITH ALL CORRECT SOLUTIONS. Internal ____ is not required for dynamic type compressors. seals lubrication pressure monitoring corrosion monitoring temperature monitoring b Low pressure or high pressure are the two primary classifications of ____. centrifugal pumps sump pumps boilers draft fans pressure controllers e The boiler feedwater becomes increasingly ____ as it approaches the measurement of zero. acidic neutral softer ba...

The best tool for adjusting and setting the pressure on an appliance regulator: a. Manometer b. Velometer c. Psychrometer d. An analyzer - Manometer 3/8 NPS black iron pipe shall? a. Not be used for propane b. Not be used in a concealed location c. Not be used for natural gas d. Not be used for indoors - Not be used in a concealed location (6.3.9) A corrugated metal gas connector connected to a range must not exceed?

Propane book Questions with Complete Solutions