welding safety

Columbia International University

Here are the best resources to pass welding safety. Find welding safety study guides, notes, assignments, and much more.

Page 2 out of 30 results

Sort by

NCCER Electrical Level 3 Module 5 'Overcurrent Protection' exam(fully solved)(verified for accuracy)
  • NCCER Electrical Level 3 Module 5 'Overcurrent Protection' exam(fully solved)(verified for accuracy)

  • Exam (elaborations) • 6 pages • 2023
  • Available in package deal
  • Worn motor bearings are most to result in a(n)___. continuous overload A high-level short circuit current may exceed ___. 50,000A` Accidental contact between an electrical conductor and a grounded enclosure is called a(n)___. ground fault Most arcing faults begin as ___. ground faults A plug fuse with a hexagonal cap has a maximum amperage rating of ___. 15A Under normal operation and at currents near its ampere rating, a fuse operates as a ___. conductor...
    (0)
  • $14.99
  • 1x sold
  • + learn more
Welding level 2 final exam questions and answers(verified for accuracy)
  • Welding level 2 final exam questions and answers(verified for accuracy)

  • Exam (elaborations) • 8 pages • 2023
  • Available in package deal
  • increase If the wire speed is increased during GMAW or FCAW work, the voltage must __________________________. tungsten In GTAW, the torch holds a (an) __________________ electrode. 120 When tapering the point on a tungsten electrode, use ______-grit grinding wheels or sanding belts for finishing. the wire to fuse to the tip If the welding voltage is set too high, the arc will be too long and could cause __________________________________________________________. ...
    (0)
  • $13.49
  • + learn more
LEVEL 1 RACEWAYS & FITTINGS NCCER MODULE EXAM QUESTIONS WITH VERIFIED CORRECT ANSWERS.docx
  • LEVEL 1 RACEWAYS & FITTINGS NCCER MODULE EXAM QUESTIONS WITH VERIFIED CORRECT ANSWERS.docx

  • Exam (elaborations) • 7 pages • 2023
  • Available in package deal
  • What is the purpose of a sealing fitting (seal off) To minimize the passage of gas vapors and flames through a conduit. What is article 344 of NEC Will be covering RMC or Rigid metal conduit What is one characteristic of aluminum conduit? It is more resistant to wet environments. When installing EMT or electrical metallic tubing it must? be supported every 10 feet EMT is often referred as? Thin wall type conduit. A type of conduit body with a 90° connecto...
    (0)
  • $15.99
  • + learn more
NCCER Electrical Level 2 Module 9 Grounding and Bonding exam questions with 100% correct answers
  • NCCER Electrical Level 2 Module 9 Grounding and Bonding exam questions with 100% correct answers

  • Exam (elaborations) • 7 pages • 2023
  • Available in package deal
  • NEC Article 250 ______. is the primary governing article for the proper use and installation of grounding and bounding. Suppose a loose connection has been exposed bare conductor and it contacts the edge of a metal enclosure. Is this an example of a short circuit or a ground fault? ground fault A single-phase system has two legs, Leg A and Leg B. If Leg A is carrying 50A and Leg B is carrying 45A, the current carried by the neutral is _____. 50A-45A=5A (Leg A- Leg B) Assu...
    (0)
  • $14.49
  • + learn more
NCCER Millwright Level II Module 7 Gaskets and Packing exam questions with 100% correct answers(verified for accuracy)
  • NCCER Millwright Level II Module 7 Gaskets and Packing exam questions with 100% correct answers(verified for accuracy)

  • Exam (elaborations) • 21 pages • 2023
  • Available in package deal
  • NCCER Millwright Level II Module 7 Gaskets and Packing exam questions with 100% correct answers(verified for accuracy)
    (0)
  • $15.49
  • + learn more
Welding Level 1 exam questions with 100% correct answers
  • Welding Level 1 exam questions with 100% correct answers

  • Exam (elaborations) • 3 pages • 2023
  • Available in package deal
  • Welding current is transferred from the electrode holder, through the ___ and into the work Wire core of the electrode The harmful oxygen and hydrogen present in the atmosphere surrounding a molten weld is pushed away from the weld by the ____ created during the welding process Gaseous shield of carbon dioxide The purpose of the specifications written by the American welding society (aws) is to set standards that all manufacturers must follow when manufacturing ____ Welding cons...
    (0)
  • $13.99
  • + learn more
Welding Level 2, Module 9 questions and answers
  • Welding Level 2, Module 9 questions and answers

  • Exam (elaborations) • 2 pages • 2023
  • Available in package deal
  • no postweld cleaning is necessary Since there is no flux in GTAW welding, ____________________. rear deflector material and a face shield. When a hard hat is required while welding, use one that allows the attachment of _____________________. any welding or cutting Approved fire extinguishers must be available before ____________________. has little or no cleaning action Clean the steel plate before welding to remove mill scale, because the direct current electrode negat...
    (0)
  • $14.99
  • + learn more
Welding Level 2, Module 8 questions with verified solutions
  • Welding Level 2, Module 8 questions with verified solutions

  • Exam (elaborations) • 3 pages • 2023
  • Available in package deal
  • GTAW If you see the label TIG on a welding machine, that machine is considered to be what kind of welding machine? oxygen During the GTAW process, UV radiation in the atmosphere near the weld can ionize ___________________. direct current electrode negative (DCEN) GTAW is most commonly performed using ___________________. 1/2 inch High voltage, high frequency current creates a very stable arc that is able to jump a gap of about _____________________. arc starting ...
    (0)
  • $14.49
  • + learn more
Welding Level 2, Module 7 questions and answers
  • Welding Level 2, Module 7 questions and answers

  • Exam (elaborations) • 2 pages • 2023
  • Available in package deal
  • flux A shielding gas can be generated entirely from the ____________________ in the electrode core. (self shielded FCAW-S) rear deflector material If a hard hat is required for the environment, use one that allows the attachment of ____________________. flash sheids When preparing to practice welding, set up ____________________ around the welding area. 30 to 37 1/2 V-groove weld coupons must be beveled at _________to___________degrees for carbon steel or low alloy plate...
    (0)
  • $14.99
  • + learn more
Nccer Plumbing Level 1 exam questions and answers(verified for accuracy).
  • Nccer Plumbing Level 1 exam questions and answers(verified for accuracy).

  • Exam (elaborations) • 18 pages • 2023
  • Available in package deal
  • The modern word for plumber is derived from the Latin word for A person who works with lead LEED applies to all areas of the profession, except Renovation Water that comes from laundry and bathtubs and reused in known as Graywater Suggested national plumbing standards are called Model codes You are offered a job by another contractor before you have fulfilled your current obligations. The professional response is to Ask the contractor to wait until you have met y...
    (0)
  • $16.49
  • + learn more