Woodshop Exama Questions and Answers

CHAPTER 26 WOODSHOP VOCABULARY EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+CHAPTER 26 WOODSHOP VOCABULARY EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+

CHAPTER 30 WOODSHOP STUDY GUIDE EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+CHAPTER 30 WOODSHOP STUDY GUIDE EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+

WOODSHOP CHAPTER 22STUDY GUIDE EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+ WOODSHOP CHAPTER 22STUDY GUIDE EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+ WOODSHOP CHAPTER 22STUDY GUIDE EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | G...

WOODSHOP SAFETY EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+WOODSHOP SAFETY EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+WOODSHOP SAFETY EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+

WOODSHOP SAFETY EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+WOODSHOP SAFETY EXAM | QUESTIONS & ANSWERS (VERIFIED) | LATEST UPDATE | GRADED A+

T/F... wear gloves when you use tools or operate any of the equipment ~ false T/F... anytime you are done with a machine, turn it off and wait until it comes to a complete stop ~ True T/F... Wear proper shoes at all time ~ True T/F... concentrate on what you are doing, give it your full a...

What is the name of the metal that is added to steel to prevent it from corroding? ~ zinc another name used to describe a sheet metal pattern is? ~ Stretched out What are the two basic classifications of sheet metal patterns? ~ Radial line and parallel line Which developments are those that...

hen starting a cut with the miter saw you should always? ~ Turn the blade on, let it reach full speed, then lower to cut On the panel saw you should always? ~ Carefully move the wood out of the way, just after the cut is complete and before letting the saw spring back into place A hand held c...

Never stand in the line of fire on any machine due to... ~ Kick back. If the material is small,... ~ You should use push sticks to aid in feeding the stock. When using the planer the initial adjustment for the machine is made while it is off... ~ All other adjustments are made while running....

True or False: the selection of bits available for the router is, unfortunately, pretty limited ~ False True or False: when using the portable router, it does not matter how much material you take off in any single pass ~ False Climb cutting (pushing the router into the board in the same d...

Miter Box ~ Nail Set ~ Tool used to drive nail heads below the surface. Oval Head Screw ~ A screw with a partially recessed head and generally used with exposed hardware like hinges. Philips Screwdriver ~ Pilot Hole ~ A drill hole that is made in material to aid the accurate insert...

Board feet (all inches) ~ T"xW"xH"/144 Board feet (height in feet) ~ T"xW"xH'/12 T is 1" or less, figure it to be... ~ 1" T is more than 1", figure it to be... ~ Exact size What's finer? 600g or 60g? ~ 60g Name the parts of the screw from top to bottom. ~ Countersink Shan...

A blade will ____ if forced to cut too fast ~ Break Turn the switch off immediately when a blade ~ Binds or bends The radial arm saw is not used for ~ Ripping Wood should be held solidly against the ~ Fence When crosscutting bowed lumber, keep the crown to the face and down on the pave...

never grab the ___________ to up tighten the bit when changing ~ sandpaper used to sand straight or curved edges on your board ~ belt sander always run the _______ system when using sanders ~ vacuum only sand on the ______ side of the sander, never the backside ~ front the size of a belt...