Papersbysue

Router - ANSWER Used for edge profiling. Power Drill - ANSWER Used for drilling holes and setting screws. Table Saw - ANSWER Used to rip wood. Miter Saw - ANSWER Used for cross cuts and finish cuts. Band Saw - ANSWER Used for curved cuts. Scroll Saw - ANSWER Used for tight and rounded cuts and intricate details. Drill Press - ANSWER Used for drilling holes. Power Sander - ANSWER Used for finish sanding. What are the stationary tools of the woodshop? - ANSWER The table saw...

Students must wear these at all times in the shop. - ANSWER Safety Glasses The red power buttons are only to be pressed by students in case of? - ANSWER Emergency This type of behavior is NEVER permitted in the shop. - ANSWER Messing Around Make sure all of these are in place before starting a machine. - ANSWER Guards What is common sense that must be practiced at all times in the shop area? - ANSWER No Phones The cutting depth of the jointer is always set to? - ANSWER 1/16"

Safety instructions must be given before you are allowed to work on or operate any machine or _______ - ANSWER tool you are not permitted to work on any equipment or machine if the ______ is not present - ANSWER instructor guards and safety device must be on all machines during _____ - ANSWER operation machinery must not be oiled or adjusted while in ____ - ANSWER use a machine must be started and stopped only by the _____ - ANSWER operator do not leave a machine while it is _____...

It is important to wear proper eye protection - ANSWER At all times,any time you are in the shop When lifting heavy objects it is important that you lift with the - ANSWER Leg muscles Checking the sharpness of any tool should be done using - ANSWER Paper or wood "HORSEPLAY" in the shop - ANSWER Is forbidden at all time and can result in your immediate dismissal Why is it safe to use sharp tools - ANSWER Less force is need to do the job Rags which are covered with e,or other chem...

1) In case you receive an injury in the shop, report it at once to your _____ - ANSWER Teacher 2) If the instructor is out of the room, all power machines must be _____ - ANSWER Off 3) All "special" machine setups (re-sawing, redoing, plowing, grooving and tapering) must be checked by the instructor before turning on the _____ - ANSWER Power 4) Adjustments on all power machines should be made before turning on the _____ - ANSWER Power 5) Scraps of lumber must be cleared away from a...

Attitude - ANSWER Horseplay will not be tolerated. This is evidence of poor safety attitude. Keep your mind on your work. Respect the rights of others and their property. Clothing and Protective Equipment - ANSWER Wearing jewelry or loose clothes in the lab is dangerous. Long hair should be tied back or worn under a cap to avoid getting it caught in the machinery. Covered toe shoes or boots with rubber soles should be worn. Always wear proper eye protection when working in the shop or w...

List the six things one should note about one self upon working in the wood shop. - ANSWER -shoes -goggles -tight clothing -mindset -jewelry -hair tied back How do you anticipate accidents before using machinery? - ANSWER by knowing the direction the blade/disk/bit moves. With a circular saw, where do you place the wood? - ANSWER on the table and fence. Where are the five emergency shut off buttons? - ANSWER -by the sanders -monitor window -student storage area -left of band saw...

What is the margin of safety? - ANSWER 4 inches. When using a saw, never... - ANSWER Feed the material faster than the saw blade can remove the wood easily. The palm sander is used for what? - ANSWER removing small amounts of material slowly. All small work should be secured with what? - ANSWER A clamp or vise. Make all adjustments on all power tools with the power off, except... - ANSWER When adjusting the speed of the lathe. Always cut.. - ANSWER Away from yourself when using a ...

Where should the saw be before starting a cut on the radial arm saw? - ANSWER Behind the fence Name the machine used to cut lumber parallel to the grain - ANSWER Table saw Where should your hands be and what should they be doing while making a crosscut on the radial arm saw? - ANSWER Your hands should never be in the path of the blade, while making a cut your left hand should hold the stock firmly against the fence at least 6 inches from the blade. Your right hand will pull the motor and ...

Safety instructions must be given before you are allowed to work on or operate any machine or - ANSWER tool You are not permitted to work on any equipment or machine if the ____________________ is not present - ANSWER instructor Guards and safety devices must be on all machines during - ANSWER operation Machinery must not be oiled or adjusted while in - ANSWER use A machine must be started and stopped only by the - ANSWER operator Do not leave a machine while it is - ANSWER runnin...