Bestofluck1

Who should a boilermaker consult about the correct hydrotest - ANSWERQuality assurance Where must workers stand while boiler tubes are x-rated - ANSWEROutside the radiation barrier limits Which gas is turn first when turning a cutting torch - ANSWERAcetylene The rim plate on a storage tank is what type of structural component - ANSWERThe highest shell ring of the tank Who provides welding procedures for high pressure vessels - ANSWERQuality control person What is the hydro pressur...

42. stationary head B - ANSWER 43. shell body f - ANSWER 44. baffles D - ANSWER 45. tube I - ANSWER 46. float tube sheet J - ANSWER 47. partition plate/ baffle A - ANSWER 48. shell H - ANSWER 49. high point bleed p - ANSWER 50. tube sheet c - ANSWER 51 float head flange M - ANSWER 52 heat exchanger report O - ANSWER 53 float head L - ANSWER 54 channel cover/ dollar plate G - ANSWER 55 float head backing device/ lock ring K - ANSWER 56 bell head N - ANSWE...

Which organization requires a person to be trained in order to operate personal lifting equipment - ANSWEROSHA Where would the usage of a RTJ Gasket be found - ANSWERHigh pressure system All of the following are examples of internal manway hardware except - ANSWERSlide fastener What type of wrench measures how much a fastener is being tightened - ANSWERTorque the fitting that makes it easy to disassemble threaded piping is - ANSWERUnion what is the purpose of a gasket - ANSWERto create a se...

The space between a thread of a bolt and its nut is called _______. - ANSWERClearance The amount of difference allowed from a standard is called _________. - ANSWERTolerance The normal method for measuring torque is _______. - ANSWERFoot-pounds (ft. lbs.) The method of measuring the amount of torque that is applied to small bolts, nuts, and screws is _______ - ANSWERInch-pounds (in lbs.) A(n) _______is a machined metal slot in a shaft and on parts such as gears and pulleys that acce...

At what angle is a chain fall usually used? - ANSWERVertical Pipeline PNID ask for what size the main line is - ANSWER12" What does the PNID ask for material - ANSWERA-335 When attaching two pipes together what fitting is used? - ANSWERCoupling When attaching two different pipe sizes together what fitting is used? - ANSWERBushing What is a tigger? - ANSWERWinch What controls water in the towers? - ANSWER(Distributors) internally installed above a packed bed. Which performs the job in prov...

1. Which organization requires a person to be trained in order to operate personal lifting equipment? - ANSWEROSHA 1. Where would the usage of a RTJ Gasket be found? - ANSWERHigh Pressure System All of the following are examples of internal man way hardware except - ANSWERSlide Fastener 1. What type of wrench measures how much a fastener is being tightened? - ANSWERTorque 1. The fitting that makes it easy to disassemble threaded piping is - ANSWERUnion 1. What is the purpose of a ...

1. Which organization requires a person to be trained in order to operate personal lifting equipment? - ANSWEROSHAThe Occupational Safety and Health Administration (OSHA) requires that persons operating personal lifting equipment, or any kind of machinery, must be properly trained. This includes training in the operation of the equipment, understanding the hazards associated with its use, and the implementation of safety precautions to prevent accidents and injuries. 2. Where would the usage ...

6_2/3 - ANSWERSubtract: 9_1/8- 2_11/24= -6 2/3 -6 1/2 -6 1/4 -6 3/4 151' - ANSWERA boilermaker mechanic needs 12 lengths of 1/4" membrane. Each Length is to be 12' 7''. What is the total length of membrane needed? -150' 7'' -150' 10'' -151' -151' 4'' 31' 2'' - ANSWERA welder needs tube sections (Dutchmen) in the following lengths: 8' 10'', 12' 5'', and 9' 11''. What is the total amount of tubing needed? -31' -31' 2'' -31' 6'' -32' 2'' 2 1...

osha - ANSWERWhich organization requires a person to be trained in order to operate personal lifting equipment? high pressure system - ANSWERWhere would the usage of a RTJ Gasket be found? slide fastener - ANSWERAll of the following are examples of internal manway except? a) football washer b) slide fastener c) half washer d) bellville washer torque - ANSWERWhat type of wrench measures how much a fastener is being tightened? union - ANSWERThe fitting that makes it easy to disasse...

When working on an exchanger tube side hydro test, the - ANSWERCHANNEL HEAD How many bolts need to be removed from a 12 bolt flange when installing gasket? - ANSWER5 One of the main factors to consider when installing an orifice plate is: - ANSWERDirection of flow When cutting a stud bolt, which end of the bolt should be saved? - ANSWER- STAMPED - STENCILED - MARKED The method of pulling and rigging out an exchanger bundle without equipment is called a CONVENTIONAL pull. - ANSWER...