Voltage tester - Study guides, Class notes & Summaries

When using a pulse load tester on a sealed lead acid battery, the minimum acceptable capacity is... Answer - 80% When a software change is made to a fire alarm system, what percentage of the initiating devices not affected by the change must be tested Answer - 10% When testing elevator recall, the elevator should go to the alternate level when: Answer - The lobby smoke detector on the recall level is activated Minimum requirement for system documentation Answer - Battery calculations/fl...

NICET Level 1 inspection and Testing Exam 2024 When using a pulse load tester on a sealed lead acid battery, the minimum acceptable capacity is... -Answer-80% When a software change is made to a fire alarm system, what percentage of the initiating devices not affected by the change must be tested -Answer-10% When testing elevator recall, the elevator should go to the alternate level when: -Answer-The lobby smoke detector on the recall level is activated Minimum requirement for system docu...

What is the first thing a tech should do when arriving at a no combustion call? - Answer- Ask how many times the customer reset the unit. What is the best long term solution for preventing a clogged nozzle? - Answer- -Remove any underground storage tanks. -Install a quality oil filter. -Cut the suction line 10" above the tank outlet to prevent sludge. Hot water and steam valves are interchangeable. - Answer- False When in the presence of a flame, a cad cell normally reads.. - Answe...

NCCER Electrical module 3 (intro to electrical circuits) Exam Questions And Answers All Verified a circuit has a source voltage of 50v and a current of 10A, what is the power in watts? - ANS 500w voltage is defined as the? - ANS driving force that makes current flow in a circuit if a circuit has 12 amps of current and the resistance is 20 ohms, the applied voltage is? - ANS 240 volts if two 10 ohm resistors are connected in series, what is the total resistance of the resistors? ...

NCTI Final Exam: Progression Field Tech 2- 3 Exam| New Update 2023/ 2024|Verified Questions and Answers 1. What would be the downstream throughput if two QAM channels with a throughput of 38 Mbps were bonded?  Answer: 76 Mbps. 2. What are two features that were added in DOCSIS 3.1 to extend the viability of HFC networks into the next decade?  Answer: OFDM and LDPC. 3. Which step in the troubleshooting process requires a discussion with the customer to gather more...

FULL NHIE EXAM PRACTICE - Questions and Answers (Complete Solutions) Where you have found evidence of footing settlement, how can you predict whether there will be further settlement? (a) You can count the number of planes of movement. (b) You can determine the type of foundation material. (c) You cannot predict settlement from a single inspection. (d) You can determine the depth of the footing. You typically identify a Freon leak (a) As an oil stain (b) As refrigerant coming out of the Freon ...

ASE-A8 Engine performance Latest 20023 Already Passed If the compression is 5 psi and the oem spec is 140 psi, what most likely is the cause? A, worn piston ring. B, burnt valve. Both A and B What most likely is the cause if the compression doesn't go up during a wet compression test? A, burnt valve. B, worn piston ring. A What most likely is the cause if the compression goes up during a wet compression test? A, burnt valve. B, worn piston ring. B 2. Blue smoke is coming from the exhaust...

Level 1 Module 12 Electrical Test Equipment Questions and Answers 2023 Which of the following devices measures ohms, amps, and volts? Multimeter Which of the following devices is also called an insulation resistance tester? Megger Which instrument should be used to verify that there is power available to run a three-phase motor that will not start? Voltage tester Which meter can measure current without having to make contact with uninsulated wires? Clamp-on anmeter What is the lowest ...

ABYC standard ________ applies to inverters A. E-2 B. A-27 C. A-28 D. A - 31 - Answer-D A true RMS voltmeter is required to accuralty check output voltage from a(n): A. non-sinusoidal output inverter B. Isolation transformer C. Inverter DC input D. Galvanic isolator - Answer-A An AC voltmeter is required at the panel if the boat is equipped with: A. A DC windlass B. An AC- powered water heater C. An inverter D. AC- powered reading lamps - Answer-C All of the following could cause ...

PICAT/ASVAB Test Exam | Questions and Answers Graded A+ Latest 2024/2025 Which of the following is NOT a pipe wrench? - CORRECT ANSWER Socket Wrench What doesn't have an electric motor? - CORRECT ANSWER Toaster In concrete work a "darby" is a - CORRECT ANSWER Type of wooden float The technique for joining copper water pipes is called? - CORRECT ANSWER Soldering A Speaker that produces high frequencies is called? - CORRECT ANSWER Tweeter What's is constantly used as a conductor?...