High starting torque Study guides, Class notes & Summaries

Z-51 Written Exam Questions and Complete Solutions In a steam turbine, what is the function of a Kingsbury thrust bearing? A) Maintain first stage steam pressure. B) Compensate for coupling misalignment. C) Adjust shaft torque at start up. D) Maintain axial positioning of the rotor shaft. - Answer: D) Maintain axial positioning of the rotor shaft. The ratio of actual pressure of water pressure in the atmosphere to the saturated pressure of given temperature is A) partial pressure....

Gleim Private Pilot FAA Knowledge Test Guide Gleim Private Pilot FAA Knowledge Test Guide What is one purpose of wing flaps? To enable the pilot to make steeper approaches to a landing without increasing the airspeed. One of the main functions of flaps during approach and landing is to: Increase the angle of descent without increasing the airspeed. What is the purpose of the rudder on an airplane? To control yaw. Which is not a primary flight control surface? A. Flaps B. Stabilat...

BGT (ATPL Systems)What is Thrust output a product of? - Mass airflow - Acceleration What is EPR? Engine pressure ratio Exhaust gas (Jet pipe) : Inlet air pressure Brainpower Read More Previous Play Next Rewind 10 seconds Move forward 10 seconds Unmute 0:02 / 0:15 Full screen What is the most important indication of thrust output in a turbojet? EPR What effect does a blocked EPR gauge have? Overread (actual power output is lower) How does high by pass e...

BGT (ATPL Systems)What is Thrust output a product of? - Mass airflow - Acceleration What is EPR? Engine pressure ratio Exhaust gas (Jet pipe) : Inlet air pressure Brainpower Read More Previous Play Next Rewind 10 seconds Move forward 10 seconds Unmute 0:02 / 0:15 Full screen What is the most important indication of thrust output in a turbojet? EPR What effect does a blocked EPR gauge have? Overread (actual power output is lower) How does high by pass e...

_____, _____, _____ & _____ is the refrigeration cycle? - Expansion; evaporation; compression & condensation A 230 volt PFC compressor tries to start at 184 volts and trips on overload protection, the starting torque of the motor is _____? - Decrease by lower voltage A A/C system with zone control is obtained by mixing hot and cold air at the central unit in response to room thermostats is a _____ system? - Multi-zone A diulating switch is used to _____. - Change proportional action to two...

Millwright Level 4 Electrical Exam Questions And Answers 100% Fuses are circuit protection devices. what fuse component provides the HRC type fuse with the ability to interrupt currents up to 300,000 Amps without failure? A. very large contacts B. parallel fusible links C. sand filled D. series fusible links C. sand filled Elements that allow a large number of electrons to flow are known as? A. insulators B. free electrons C. conductors D. electromotive force C. conductors The ato...

Millwright Level 4 Electrical Exam Questions And Answers 100% Fuses are circuit protection devices. what fuse component provides the HRC type fuse with the ability to interrupt currents up to 300,000 Amps without failure? A. very large contacts B. parallel fusible links C. sand filled D. series fusible links C. sand filled Elements that allow a large number of electrons to flow are known as? A. insulators B. free electrons C. conductors D. electromotive force C. conductors The ato...

AMT2 SWE elaborated questions and answers 2024/2025 How do you clean helmet visor? - CORRECT ANSWER-SOFT CLOTH AND MILD SOAP SOLUTION; RINSE WITH CLEAN WATER. IAW 13520.1B ENCL 4-31 How do you clean flight gloves? - CORRECT ANSWER-1. DON THE GLOVES. 2. WASH WITH SOAP AND WATER AS IF WASHING HANDS. 3. WHEN GLOVES ARE CLEAN, RINSE AND REMOVE FROM HANDS. 4. SQUEEZE, BUT DO NOT WRING GLOVES TO REMOVE EXCESS WATER. 5. PLACE THE GLOVES FLAT ON A TOWEL, AND FOLD THE TOWEL TO COVER GLOVES MA...

For a given number of poles, which of the following determines the speed of an AC motor? Frequency The terminals of a motor can be identified using a battery and a(n) _____. voltmeter The stationary magnet of a DC motor is represented by the ______. field poles Any exposed live parts must be guarded if they are operating at ______. 50V or more between terminals The synchronous speed at which a four-pole, 60Hz induction motor operates is _____. 1,800rpm In ...

Millwright Level 4 Electrical Exam Questions And Answers 100% Fuses are circuit protection devices. what fuse component provides the HRC type fuse with the ability to interrupt currents up to 300,000 Amps without failure? A. very large contacts B. parallel fusible links C. sand filled D. series fusible links C. sand filled Elements that allow a large number of electrons to flow are known as? A. insulators B. free electrons C. conductors D. electromotive force C. conductors The ato...