Hic exam questions stuvia - Study guides, Class notes & Summaries

The MOST specific information about the size and location of windows would be found in a - ANSWER-Floor plan What direction does heat flow? - ANSWER-Hot to cold What are batter boards - ANSWER-stakes and ledger boards marking building lines What is the MAXIMUM distance between a ventilating opening in an under-floor space and each corner of the building? - ANSWER-3 feet What is NOT required in exterior nonbearing walls? - ANSWER-Load-bearing headers A lengthwise grain separation b...

The MINIMUN length drywall screw for installing 1/2 inch gypsum board to wood studs is - ANSWER-1 1/4 inches What is the MINIMUM breaking strength required of safety belt lanyards - ANSWER-5,400 pounds What is the MINIMUM clearance that combustible insulation MUST other heat-producing devices - ANSWER-1 inch What is the MAXIMUM flame spread index for insulation materials - ANSWER-25 The amount of water per sack of cement is what controls all EXCEPT - ANSWER-Wear resistance The esc...

What is directly affected by the surface and subsurface conditions of the building site? - ANSWER-Foundations - While the type and size of a structure will partly determine the type of foundation, the foundation itself is very much affected by the surface and subsurface conditions of the building site. What term is used to describe the act of removing air pockets from setting concrete? - ANSWER-Vibrating Concrete - Consolidation is a process that removes air pockets and forces the concrete in...

What is the MINIMUM breaking strength required of safety belt lanyards - ANSWER-5,400 pounds What is the MINIMUM clearance that combustible insulation MUST other heat-producing devices - ANSWER-1 inch What is the MAXIMUM flame spread index for insulation materials - ANSWER-25 The amount of water per sack of cement is what controls all EXCEPT - ANSWER-Wear resistance The escape device for a trench over 4 feet deep MUST be within a MAXIMUM of - ANSWER-25 feet of the worker What is t...

what kind of solvent (zuulruulegch) can be used on oil-based paints - ANSWER-Turpentine P950 where should one start painting a room - ANSWER-ceiling what type of drywall is used that is fire resistant to ceiling - ANSWER-Type C p916 What is the minimum width of a main entrance door in residential construction? - ANSWER-3' equivalent to 36" what type of gypsum is used in veneer plaster system - ANSWER-Blue board drywall ceiling and end butt joints should be - ANSWER-taped In a...

The MINIMUN length drywall screw for installing 1/2 inch gypsum board to wood studs is - ANSWER-1 1/4 inches What is the MINIMUM breaking strength required of safety belt lanyards - ANSWER-5,400 pounds What is the MINIMUM clearance that combustible insulation MUST other heat-producing devices - ANSWER-1 inch What is the MAXIMUM flame spread index for insulation materials - ANSWER-25 The amount of water per sack of cement is what controls all EXCEPT - ANSWER-Wear resistance The esc...

what type of coating will not chalk when applied to exterior walls - ANSWER-Latex paint what kind of solvent (zuulruulegch) can be used on oil-based paints - ANSWER-Turpentine P950 where should one start painting a room - ANSWER-ceiling what type of drywall is used that is fire resistant to ceiling - ANSWER-Type C p916 What is the minimum width of a main entrance door in residential construction? - ANSWER-3' equivalent to 36" what type of gypsum is used in veneer plaster system ...

To avoid hardening due to hydration ....use masonry mo before? - ANSWER-2 1/2 Hours Heat flows in what direction ? - ANSWER-Hot to Cold First and most important step in using or preparing a material ? - ANSWER-Thoroughly read and understand the manufactures directions . whats true abou the gypsum broads over wood framing ? - ANSWER-Apply First to ceiling , then to wall What is used to remove air pockets from place concrete ? - ANSWER-Vibration wide square-edged boards are to be us...

Nailing into hard wood, whats best to use ? - ANSWER-Cut na To avoid hardening due to hydration ....use masonry mo before? - ANSWER-2 1/2 Hours Heat flows in what direction ? - ANSWER-Hot to Cold First and most important step in using or preparing a material ? - ANSWER-Thoroughly read and understand the manufactures directions . whats true abou the gypsum broads over wood framing ? - ANSWER-Apply First to ceiling , then to wall What is used to remove air pockets from place concret...

What is the MAXIMUM distance between a ventilating opening in an under-floor space and each corner of the building? - ANSWER 3 feet What is NOT required in exterior nonbearing walls? - ANSWER Load-bearing headers A lengthwise grain separation between or through the growth rings of lumber is called a - ANSWER Shake (c 326) The abbreviation "d" in "16d" means - ANSWER Penny Notches may not be located in the ____________ of a joist span - ANSWER Middle 1/3 How should boar...