Fire pump run - Study guides, Class notes & Summaries

Boilermaker NCCR Test Questions And Answers Boilermaker NCCR Test 1 ft 3-3/4 in + 2 ft 1-1/16 in +5 ft 10- 7/8 in = - ANS 9 ft 3-11/16 in A 1-inch plate is to be cut. Why should an acetylene gerulator on a cutting rig not be adjusted over 15 PSI? - ANS Acetylene is unstable above this pressure A big control valve is pulled who is responsible for the rigging? - ANS Crane operator and rigger A boiler maker must have all of the following wh...

What is the main reason for assuming the HELP position when you are stranded in the water? - ANSWER-reduces heat loss What is the important safety information found on a boat's capacity plate? - ANSWER-maximum weight and/or number of people the boat can carry safely What is the best way to avoid overloading your boat? - ANSWER-Don't exceed the limits listed on the capacity plate. What should you leave with a friend or relative before a long outing on the water? - ANSWER-float plan Wh...

Certificate of Fitness for Citywide Sprinkler Systems (S-12) S-12 CITYWIDE SPRINKLER SYSTEMS, S12 sprinkler test Spring 2023. THE __________ IS RESPONSIBLE TO MAINTAIN SPRINKLER SYS. AND TO DETERMINE QUALIFICATIONS. RECORDS OF ALL INSPECTIONS AND MX SHALL BE MAINTAINED ON PREMISES FOR A MIN. OF __________ YEARS. THE BUILDING OWNER SHALL ASSIGN A(N) ____________ TO COMPLY WITH REQUIREMENTS. REGULAR MX AND MINOR REPAIRS NOT AFFECTING MORE THAN ________ FLOOR(S) ARE CONSIDERED PLANN...

General Maintenance/ Boma Questions and Answers 100% Pass When Starting a centrifugal pump That is part of a manifold with no check valves You should open the suction valve, start the pump and open the discharge valve slowly Curb cock A Valve insert it in a water line between the corporation stop and the water meter is generally called To check sheave wear Measure each groove angle Variable pitch sheaves may be used in some cases to provide which of the following types of speec...

Fire Pump Run Test Practice Quiz/60 Questions and Answers

Diesel engine fuel tank level, float switch and solenoid valve operation shall be checked __________. - weekly (visual inspection) The pertinent visual observation categories required to be inspected weekly checklists are: - Pump house conditions, pump system conditions, electrical system conditions, diesel engine system conditions, steam engine conditions Heat exchangers shall be checked for __________ water flow. - cooling All alarm pilot lights should be in what state? - Off There are ...

Lesson 28 Providing a Secure and Safe Environment A hospital nurse transcribing a primary health care provider's prescriptions for a client is unable to read a prescribed dosage because the primary health care provider's handwriting is unclear. Which action should the nurse take? Call the primary health care provider Ask the client about the usual dosage of the medication Call the pharmacy to ask about the usual dosage of the prescribed medication Contact the nursing supervisor for ...

Type of sealant you should you use on a Phil-Tite Ball Float nipple: correct answers Pipe dope Number of open valves on the clean air separator: correct answers One You must be CERTIFIED by Healy to re-connect a Healy breakaway, True or False? correct answers False The type of pressure gauge is recommended to test Healy Vac correct answers SYSA gauge measuring 0-100 WC On new construction, after July 1, 2004, Can you install an in-ground Spill Bucket? correct answers YES-When Piping ...

Z-51 Written Exam Questions and Complete Solutions In a steam turbine, what is the function of a Kingsbury thrust bearing? A) Maintain first stage steam pressure. B) Compensate for coupling misalignment. C) Adjust shaft torque at start up. D) Maintain axial positioning of the rotor shaft. - Answer: D) Maintain axial positioning of the rotor shaft. The ratio of actual pressure of water pressure in the atmosphere to the saturated pressure of given temperature is A) partial pressure....

IFSTA Chapter 21 QuizWhich duty would be performed by a qualified technician instead of a Fire Fighter II? Select one: a. Checking equipment oil and fuel levels b. Inspecting spark plugs for damage c. General inspection of portable generators d. Detailed maintenance of lighting equipment - correct answer d. Detailed maintenance of lighting equipment Which pieces of equipment are necessary to service test a fire hose? Select one: a. Pneumatic or hydraulic testing machine and hose drying...

The basic methodology of the fire investigation should rely on the use of a ______________________ and attention to all relevant details. a. systematic approach b. approximation approach c. methodology approach d. general approach - ANSWER-a. systematic approach With few exceptions, the proper methodolgy for a fire or explosion investigation is to first _____________________ then investigate the cause, circumstances, conditions, or agencies that brought the ignition source, fuel, and ox...

Fire Pump Run Test Practice Quiz with 100% Correct Answers Heat exchangers shall be checked for __________ water flow. - Answer️️ - cooling All alarm pilot lights should be in what state? - Answer️️ -Off There are two requirements listed under pump house conditions: - Answer️️ -Ventilating louvers are free to operate & Heat is adequate, at least 40°F for diesel pump rooms __________ inspection requires verification that the pump suction discharge and bypass valves should b...