Brake hydraulic Study guides, Class notes & Summaries

Class F - GA study guide actual exam with correct answers Georgia driver’s license What is the most important reason for doing a vehicle inspection? - CORRECT ANSWER-Safety. Safety for yourself and other road user. What things should you check during a trip? - CORRECT ANSWER-Watch gauges, mirrors, and use your senses to check for problems...LOOK, LISTEN, AND SMELL. Name some key steering system parts. - CORRECT ANSWER-steering wheel, tie rod, steering shaft, hydraulic fluid reserv...

JLTV Test B Questions and Answers Already Passed Which is the only JLTV variant with a two-seat configuration? A. GP B. HGC C. CCWC D. UTL D. UTL Which of the following lights indicates that you will NOT be able to adjust the ride height? A. LVD B. SPNSN ERROR C. SPNS NOT LEVEL D. CTIS FAULT B. SPNSN ERROR What are the benefits of the vehicle design using half shafts instead of straight axles on the JLTV? A. To account for angles produced by suspension movement. B. To ensu...

Georgia Class F driver’s license questions and answers 100% pass At 55 mph approximately how many seconds does it take to come to a stop 6 seconds What is the minimum tread depth required in the front two tires 4/32" tread depth required in the front two tires There must be no more than ________ play in the steering wheel or __" in a 20" steering wheel 10 degrees/ 2" What is the minimum tread depth required in the rear tires? 2/32" tread depth required in the rear tires How do you tes...

Brake Hydraulic components Test with Complete Solutions If the brake pedal linkage is not adjusted correctly, brake fluid may not be able to expand back into the reservoir through the ________________ port of the master cylinder when the brakes get hot. • compensating • outlet • inlet • secondary - Answer-compensating The primary brake circuit fails due to a leak in the lines. Technician A says that the driver will notice a lower than normal brake pedal and reduced braking pow...

2024 TEXAS CDL AIR BRAKES UPDATED&VERIFIED 100% SOLVED GUARANTEED SUCCESS Air brake systems combine what three different systems? - ANS-Service brakes, parking brakes and emergency brakes. When should you drain the air tanks? - ANS-After every working day. Why drain water from the compressed air tanks? - ANSWater can freeze in cold weather and cause brake failure. Air brake equipped vehicles must have: - ANS-A supply pressure gauge and warning signal when psi drops below 60. What can ...

CDL Class A License Questions and Answers 100% Pass What is the most important reason for doing a vehicle inspection? Saftey for yourself and for other road users. What things should you check during a trip? 1. Instruments 2. Air Pressure Gauge 3. Temperature Gauges 4. Pressure Gauges 5. Ammeter/Voltmeter 6. Mirrors 7. Tires 8.Cargo 9. Lights Name 7 key steering system parts? 1. Tie Rod 2. Steering Column 3. Gear Box 4. Resevoir 5. Steering Knuckle 6. Draglink 7. Spindle Name some suspension...

Brake Hydraulic Systems Chapter 94 Test Questions with Correct Answers Two Techs are discussing master cylinders. Tech A says that it is normal to see fluid movement in the reservoir when the brake pedal is depressed. Tech B says a defective master cylinder can cause the brake pedal to slowly sink to the floor when depressed. Which Tech is correct? - Answer-Both If the brake pedal linkage is not adjusted correctly, brake fluid may not be able to expand back into the reservoir through th...

The brakes are being bled on an older vehicle equipped with a quick take up valve in the master cylinder. Technician A says the quick take up valve must be depressed. Technician B says the brakes on this vehicle cannot be bled. Who is right? a. A only b. B only c. Both A and B d. Neither A nor B Both technicians are wrong. The brakes on quick take up systems use the same bleeding procedure as those without this valve. A spongy brake pedal may be caused by: a. ABS Diagnostic Trouble Co...

ASE Brakes A5 Test (Exam 1, 2, 3) Questions with 100% Correct Answers | Latest 2023/2024 A drum is chattering on the brake lathe. This could be a result of a. failure to install the dampening belt b. cutting too slowly c. dull cutting blades d. cutting speed too fast -- A : failure to install the dampening belt why : a missing dampening belt could cause the drum to vibrate while on the lathe. this vibration can cause the drum to bounce on the cutting tip and make a chattering noise A veh...

Michigan ASE Brake Certification Exam Questions And Answers (Verified And Updated) Air in Hydraulic System - answerA spongy brake pedal may be caused by Excessive tire pressure - answerCan not cause very erratic brake pulling while applying brakes Excessive brake pedal travel - answerA power assist brake booster push rod that is too short will cause Brake drum machined beyond its limits - answerCan cause brake pedal fade Repair leak and replace brake linings - answerHow to correctly ser...