Appliance regulator - Study guides, Class notes & Summaries

The best tool for adjusting and setting the pressure on an appliance regulator: a. Manometer b. Velometer c. Psychrometer d. An analyzer - Manometer 3/8 NPS black iron pipe shall? a. Not be used for propane b. Not be used in a concealed location c. Not be used for natural gas d. Not be used for indoors - Not be used in a concealed location (6.3.9) A corrugated metal gas connector connected to a range must not exceed?

Sprinkler system must NOT be shut off or impaired while hot work is performed - Answer-Place damp cloth guards on individual sprinkler heads The person conducting the fire watch ______ have other duties - Answer-CANNOT A portable fire extinguisher with a rating of _________ is required and should be within ____ feet travel distance hot work area - Answer-2-A:20-B:C///30 For ROOFING OPERATIONS, a portable fire extinguisher with a minimum rating of ______ is required - Answer-3-A:40-B:C Fir...

LP-Gas Texas Bobtail Questions and Answers 100% Pass required for all piping systems that serve _______ psig appliance systems. normally operated at 11 in WC pressure 1/2 required for all piping systems that serve 1/2 psig appliance systems. normally operated at ______ in WC pressure 11 above group LP-gas containers must not be located within ____ feet of the vertical plane beneath overhead electric power lines that are over _____ volts 6 600 Fire Extinquishers must have minimum capacity of ...

G2 Exam Prep 1. The best tool for adjusting and setting the pressure on an appliance regulator: a. Manometer b. Velometer c. Psychrometer d. An analyzer: Manometer 2. 3/8 NPS black iron pipe shall

FDNY S-92 Questions and Answers Rated A+ The following are types of what? LPG, CNG, piped natural gas or solid fuel (coke). Portable fueled salamanders/space heaters National Institute for Occupational Safety and Health (NIOSH) Recommended Exposure Limit (REL) for carbon monoxide 35 parts per million (ppm) over an 8 hour period What is the third leading cause of fires in buildings under construction ? temporary heating What is direct heat flow through matter? CONDUCTION What is the transport...

What date was the sale of CFC's & HCFC's restricted to technicians certified in refrigerant recovery? - Correct answer-November 14, 1994 Section 608 of the Federal Clean Air Act requires technicians to what? - Correct answer-Recover all refrigerants. The objective of the Clean Air Act is to protect what? - Correct answer-The earth's stratosphere. HFC's - Correct answer-HydroFlouroCarbon's CFC's - Correct answer-ChloroFluoroCarbon's ODP - Correct answer-Ozone Depletion Potential Which in...

Ontario Gas G1 Practice Exam Prep B149.3-10 Questions and answers with 100% Complete Solutions | verified &updated 2024 What is the first action 'to be taken when performing an ignition spark response test? - Close test firing valve and pilot valve A valve not considered 100% shutoff - Butterfly valve The "Bleed" valve on a double block&bleed system is required on an appliance firing over? - Where is the low pressure switch located on the valve train? - After the main gas regulator Wher...

Gas Technician G2 Exam Review (Latest 2024/ 2025) Questions and Verified Answers| 100% Correct| Grade A Q: A regulator is sized for the load it is to serve by: Answer: Checking the appliance rating place and selecting a regulator for that input range. Q: A propane vaporizer shall not raise the pressure in a tank in excess of: Answer: 215 PSIG Q: Which of the following best describes a bellows type meter? Answer: One which uses pressure differential across an...

G2 Gas Technician Exam (2024/ 2025 Update) Questions and Verified Answers| 100% Correct| Grade A Q: Installation of a propane tank under 1000 USWG what would be the minimum distance from a regulator to a building opening? Answer: 3' Q: If an appliance is less than 85% efficient and non positive it would be considered a? Answer: Category 2. Q: For a steam boiler what would be the most important safety control? Answer: Low water cut off. Q: For a low pressure s...

What is the first thing a tech should do when arriving at a no combustion call? - Answer- Ask how many times the customer reset the unit. What is the best long term solution for preventing a clogged nozzle? - Answer- -Remove any underground storage tanks. -Install a quality oil filter. -Cut the suction line 10" above the tank outlet to prevent sludge. Hot water and steam valves are interchangeable. - Answer- False When in the presence of a flame, a cad cell normally reads.. - Answe...