3 axes of an airplane - Study guides, Class notes & Summaries

Force necessary to overcome gravitational force to keep the airplane flying is termed - ANSWERSLift Ailerons are used primarily to - ANSWERSRoll the airplane Ailerons are located - ANSWERSOn the outer edge of the wings Pitch makes the airplane - ANSWERSGo up and down Bank makes the airplane - ANSWERSRoll or turn The four aerodynamic forces acting on an airplane are - ANSWERSDrag, lift, thrust and weight An airplane wing is designed to produce lift resulting from relatively - AN...

Chord - Answer-Straight line joining leading edge to the trailing edge Camber line - Answer-Line which runs midway between upper and lower surfaces of the airfoil joint the trailing and leading edge. Camber - Answer-The measure of the curvature of the airfoil. Expressed as a percentage Angle of attack - Answer-The angle between the chord of the wing and the relative airflow Centre of pressure - Answer-Lift and drag act through the centre of pressure of the wing. The centre of pressure mov...

Jeppsen Private Pilot Stage 1-3 Exam (2024) || Complete Questions & 100% Correct Answers Jeppsen Private Pilot Stage 1-3 Exam (2024) || Complete Questions & 100% Correct Answers What are the characteristics of a monocoque airplane structure? - ANSWER - Almost all structural loads are carried by the outer skin of the airplane. Which control surfaces are usually located on the empennage? - ANSWER - Rudder, elevator, stabilator What condition must be present for carburetor ice to form? - ...

Angle of Attack - correct answer Angle formed by the chord line of the wing and the oncoming airflow Camber - correct answer Curvature of the top of a wing or airfoil A/C Right-of-Way: Approaching for a landing... - correct answer A/C with the lower altitude has the right of way Wing Aspect Ratio - correct answer Ratio of the distance between the wing tips of an airplane to its average wing width 1) Aspect ratio = b^2/s; where "b" is wingspan and "s" is surface area of the ...

Question 1 Correct 6.00 points out of 6.00 The main pipe coming into a factory is 8 m in diameter, and the water in that pipe enters the building at 1 m / s. Once inside, however, the pipe divides into four pipes that are each4 m in diameter. Which of the following is the velocity of the water in the smaller pipes? Select one: a. 2 m / s b. 4 m / s c. 0.25 m / s d. The velocity in the smaller pipes is the same as the velocity in the larger pipe. Question 2 Correct 6...

Private Pilot Stage 1 Exam Questions and Answers Graded A+ What is single-pilot resource management (SRM)? a. A set of step-by-step procedures you can apply to any scenario to ensure the successful completion of a flight. b. Effective use of all available resources-- human resources, hardware, and information--by a cockpit crew. c. The art and science of a pilot managing all available resources to ensure the successful completion of a flight. c. The art and science of a pilot managing all av...

Force necessary to overcome gravitational force to keep the airplane flying is termed Lift Ailerons are used primarily to Roll the airplane Ailerons are located Outer edge of the trailing edge of the wing Pitch makes the airplane Go up and down Bank makes the airplane Roll or turn The four aerodynamic forces acting on an airplane are Lift, weight, thrust, drag An airplane wing is designed to produce lift resulting from relatively High pressure bel...

What is the function of a vortex generator it is used to delay or prevent the separation of the boundary layer What are the 3 axes of an airplane longitudinal, lateral and vertical Brainpower Read More Previous Play Next Rewind 10 seconds Move forward 10 seconds Unmute 0:00 / 0:15 Full screen What are the 3 primary flight controls of an aircraft ailerons, rudder, elevator Name several secondary flight controls and describe their general purpose secondary fl...

Question 1 Correct 5.00 points out of 5.00 A 0.200 kg dart is fired horizontally at a speed of 2.75 m / s when it hits a 0.700 kg block ofwood suspended by a string. The nose of the dart sticks into 0.00210 m the wood. Together the dart and block swing upwards from a height of 0.0500 m above a table to 0.128 m above the table. Which of the following is the average force the dart applies to the block during impact? Select one: a. 32.4 N b. 15.1 N c. 1.36 N d. 0.872 N Straighterl...

PLTW Aerospace Exam Questions With 100% Correct Answers. Aerospace Engineer - answerDevelops new technologies for use in aviation, defense systems, and space exploration, often specializing in areas such as structural design, guidance, navigation and control, instrumentation and communication, and production methods. Aircraft - answerA device that is used or intended to be used for flight in the air. ATC - answerAir Traffic Control, A system is to prevent a collision between aircraft oper...