What type of wire nut - Study guides, Class notes & Summaries

Millwright - Power Transmission Exam Questions With Correct Answers 1. Calculate the accurate belt length for the following: Large diameter pulley is 11.25" and the small diameter pulley is 6.125". Shaft centers are 17.5" apart. a. 62.65" b. 62.00" c. 73.98" d. 62.28" - ANSWER- a. 62.65" L=2C+1.57(D1+d2)+[(D1-d2)²/4C] L=2(17.5)+1.57(11.25+6.125)+[(11.25-6.125)²/4(17.5)] L=35+27.27875+(26.265625/70) L=62.65 2. The clearance of meshing gears of any diametral pitch is...

Real Asvab Test 121 Questions with Verified Answers A square has how many sides? - CORRECT ANSWER 4 How much is 2 plus 2? - CORRECT ANSWER 4 A rose is a what? - CORRECT ANSWER A flower What is the best explanation of how a smooth round stone became smooth? - CORRECT ANSWER It was in a stream for a long time If you place bean seeds between moist paper towels and watch the stem leaves appear you will see a demonstration of? - CORRECT ANSWER germination Any astronomical body that ...

PICAT/ASVAB Exam 193 Questions with Verified Answers Which of these is the best explanation of how a smooth round stone became smooth? - CORRECT ANSWERS It was in a stream for a long When a lobster grows a claw to replace one that was lost, the process is called - CORRECT ANSWERS regeneration. Any astronomical body that revolves around a larger body is called - CORRECT ANSWERS a satellite. In chemistry, to be classified as an organic substance, a substance must contain - CORRECT ANSW...

Boilermaker NCCR Test Questions And Answers Graded A+ Boilermaker NCCR Test 1 ft 3-3/4 in + 2 ft 1-1/16 in +5 ft 10- 7/8 in = - ANS 9 ft 3-11/16 in A 1-inch plate is to be cut. Why should an acetylene gerulator on a cutting rig not be adjusted over 15 PSI? - ANS Acetylene is unstable above this pressure A big control valve is pulled who is responsible for the rigging? - ANS Crane operator and rigger A boiler maker must have all of the fo...

Millwright Level 2 – Bearings Questions and Answers Already Passed What are the principle parts of a friction bearing housing? Base, Base bolt slots, cap and cap bolt holes. What are friction bearing housings made from adn what factors influence the choice of housing? Cast Iron, Cast Steel, Fabricated Steel. Choice depends on the Load, The Rotational Speed, the Direction of Pull and the Support Design How are friction bearing dimensions expressed? In a fraction of their nominal size. Do all...

what tool is used to remove a module from an electric assembly? - chip puller silicon chips are used to what? - integrated circuits a multimeter does not measure - frequency Which of the following is smallest in size and can simplify electrical signals? - relay what kind of energy is converted to electrical energy by a car battery? - chemical which of the following can not be used to store an electrical charge? - fuse when current flow is interrupted by a blown fuse, the circui...

SOLAS Quiz 4 with complete solution; summer 2023 On which type davit does the davit head stay at the same height? A. Radial B. Sheath-screw C. Quadrantal D. Gravity Ans A Which type of davit is not considered to be a mechanical davit? A. Sheath-screw boom B. Radial C. Crescent D. Quadrantal Ans B A mechanical davit is designed to automatically __________. A. position the boat at the embarkation station B. lift the boat off the inboard chocks C. energize the winch for the fa...

Automotive Technology II Final Exam Study Guide Already Passed In a drum brake assembly, which brake shoe provides the most friction for slowing/stopping a vehicle? Secondary Technician is retracting caliper piston in order to replace disc brake pads. What step should be taken before tightening C-Clamp Open Bleeder Valve Technician in reinstalling hub type rotor assembly. What should be checked prior to installing rotor assembly? Wheel Stud Condition Technician is performing a hydro-...

TSSA Exam Study Questions with Correct Answers Which of the following lists best describes the key safety categories which should be considered by a fuel technician in Ontario - Answer-Personal Safety, Tools, Equipment, safety of others, site, OHSA, Ontario fuel codes What should a fuel technician do when a new piece of equipment is introduced for use - Answer-Get a copy of the user manual and read it before using the equipment What does OHSA stand for - Answer-Occupational Health and ...

  Sprinkler System - Answer: A fire extinguishing system, other than a water mist system, that utilizes water as the extinguishing agent. Automatic/Non-Automatic Sprinkler Systems - Answer: Shall be inspected by a competent person holding a S12 CoF and employed or contracted by the owner, to see that all parts of the system are in good working order, and that the fire department connections, if any, are ready for immediate use by the fire department. 6 Extra Sprinkler Heads - Answer:...