Ase brakes exam - Study guides, Class notes & Summaries

ASE BRAKES Exam 1 Questions and Answers Rated A A - Answer ️️ -A drum is chattering on the brake lathe. This could be the result of: A. Failure to install the dampening belt. B. Cutting too slowly. C. Dull cutting blades. D. Cutting speed too fast. C - Answer ️️ -A vehicle is equipped with a hydro-boost brake system has a hard pedal with little braking action. Which of the following could be the cause? A. Low brake fluid B. Air in the brake fluid C. Low power steering fluid D...

ASE BRAKES Exam #1|Complete Answers Graded A+ A A drum is chattering on the brake lathe. This could be the result of: A. Failure to install the dampening belt. B. Cutting too slowly. C. Dull cutting blades. D. Cutting speed too fast. C A vehicle is equipped with a hydro-boost brake system has a hard pedal with little braking action. Which of the following could be the cause? A. Low brake fluid B. Air in the brake fluid C. Low power steering fluid D. An overtightened power steerin...

A - Answer- The goal of burnishing the brakes after a complete brake service is to: A. Heat the brake assembly. B. Cool the brake assembly. C. Set the wheel bearings. D. Stretch the brake shoes to match the drum. A - Answer- Which of the following is true concerning master cylinder pushrod adjustment? A. There should be a slight gap between the pushrod and master cylinder piston. B. It should be adjusted until the piston is pushed in slightly. C. It should keep a slight pressure in th...

T4 ASE Brakes Exam with complete Graded A+ solutions Which of the following could cause the brakes on a truck to wear too fast? A. glazed drums B. wrong linings installed C. Low air pressure D. governor cut out pressure B. wrong linings installed which of the following could cause one brake on a truck to wear faster than the others? A. mismatched service brake chambers B. mismatched parking chambers C. low air pressure in service tanks D. governor cut out too low A. mismatched se...

A - correct answer A drum is chattering on the brake lathe. This could be the result of: A. Failure to install the dampening belt. B. Cutting too slowly. C. Dull cutting blades. D. Cutting speed too fast. C - correct answer A vehicle is equipped with a hydro-boost brake system has a hard pedal with little braking action. Which of the following could be the cause? A. Low brake fluid B. Air in the brake fluid C. Low power steering fluid D. An overtightened power steering belt D - co...

ASE Brakes A5 Test (Exam 1), ASE A5 Brakes, ASE Brakes A5 (Exam 3 ), ASE Brakes A5 Test ( Exam 2 ) – Questions & Answers

ASE BRAKES Exam #3 Questions and Answers (Graded A)

ASE A5 BRAKES EXAM NEWEST ACTUAL EXAM COMPLETE 240 QUESTIONS AND CORRECT DETAILED ANSWERS (VERIFIED ANSWERS) |ALREADY GRADED A+||BRAND NEW!!

A - Answer- The brakes are dragging on a vehicle. This could be caused by: A. Overfilled master cylinder reservoir. B. Low vacuum to the booster. C. Bypassing master cylinder. D. Quick take-up valve stuck open. B - Answer- The brake pads are worn at an angle on a vehicle with a sliding brake caliper system. Which of the following is the most likely cause? A. Worn caliper piston B. Worn caliper bushings C. Leaking caliper seal D. Leaking caliper boot C - Answer- A diagnostic troubl...

Michigan ASE Brake Certification Exam Questions And Answers (Verified And Updated) Air in Hydraulic System - answerA spongy brake pedal may be caused by Excessive tire pressure - answerCan not cause very erratic brake pulling while applying brakes Excessive brake pedal travel - answerA power assist brake booster push rod that is too short will cause Brake drum machined beyond its limits - answerCan cause brake pedal fade Repair leak and replace brake linings - answerHow to correctly ser...