Woodshop 2 exam - Study guides, Class notes & Summaries
Looking for the best study guides, study notes and summaries about Woodshop 2 exam? On this page you'll find 54 study documents about Woodshop 2 exam.
Page 3 out of 54 results
Sort by
-
Woodshop Final Exam Review |Graded A+
- Exam (elaborations) • 2 pages • 2024
- Available in package deal
-
- $9.50
- + learn more
Woodshop Final Exam Review |Graded A+ 
Margin of Safety: Table Saw 
4" 
Margin of Safety: Radial Arm Saw 
6" 
Margin of Safety: Band Saw 
2" 
Margin of Safety: Jointer 
4" 
Margin of Safety: Planer 
N/A 
Margin of Safety: Sanders 
N/A 
Margin of Safety: Chop Saw 
4" 
How to square a board: 
1. Joint one edge 
2. Rip board to desired width 
3. Trim one end 
4. Measure cut opposite end to desired length 
Board feet (all inches) 
T"xW"xH"/144 
Board feet (height in feet) 
T"xW"xH'/12 
T ...
-
Bundle For Woodshop Exam Questions with All Correct Answers 100% Verified
- Package deal • 11 items • 2023
-
- $18.09
- + learn more
1
Exam (elaborations)
Woodshop Final Exam Questions and Answers All Correct

2
Exam (elaborations)
Woodshop Exam Questions with Correct Answers

3
Exam (elaborations)
Woodshop Safety Exam Questions and Answers All Correct

4
Exam (elaborations)
Woodshop midterm review Questions and Answers

5
Exam (elaborations)
Woodshop Midterm Exam Questions with
-
Woodshop Final Exam Questions and Answers All Correct
- Exam (elaborations) • 6 pages • 2023
-
Available in package deal
-
- $13.49
- + learn more
Woodshop Final Exam Questions and Answers All Correct 
 
Hardwood lumber is commonly sold by the - Answer-board foot 
 
Softwood comes from the evergreen or needle-bearing trees that are called - Answer-conifers 
 
The best grade for hardwood lumber is - Answer-FAS 
 
A standard size sheet of plywood is - Answer-4x8 
 
This type of plane is 14 inches long with a 2-inch cutter, and is a general-purpose plane - Answer-jack plane 
 
A ___ joint is easy to make but not as strong as many other joint...
-
Woodshop Midterm exam with correct answers
- Exam (elaborations) • 9 pages • 2024
-
Available in package deal
-
- $10.49
- + learn more
Woodshop Midterm exam with correct answers 
Band Saw: Wheel doors must be closed and the __________ properly adjusted before turning on the machine. Answer-blade 
 
Band Saw: Adjust the guard so that it is __________ above the stock to be cut. Answer-¼" 
 
Band Saw: Allow the saw to reach full __________ before you begin the cut. Answer-speed 
 
Band Saw: The stock must be held __________ on the table. Answer-flat 
 
Band Saw: Feed the __________ only as fast as the machine can make the cut. A...
-
Woodshop Final Exam Review 2024
- Exam (elaborations) • 1 pages • 2024
- Available in package deal
-
- $8.49
- + learn more
Woodshop Final Exam Review 2024 
Margin of Safety: Table Saw -Answer-4" 
Margin of Safety: Radial Arm Saw -Answer-6" 
Margin of Safety: Band Saw -Answer-2" 
Margin of Safety: Jointer -Answer-4" 
Margin of Safety: Planer -Answer-N/A 
Margin of Safety: Sanders -Answer-N/A 
Margin of Safety: Chop Saw -Answer-4" 
How to square a board: -Answer-1. Joint one edge 
2. Rip board to desired widt
Get paid weekly? You can!
-
Woodshop Chapter 25 Vocabulary Exam Questions with Correct Answers
- Exam (elaborations) • 6 pages • 2023
-
Available in package deal
-
- $12.99
- + learn more
Woodshop Chapter 25 Vocabulary Exam Questions with Correct Answers 
 
The bevel angle on a sliding compound miter saw can be set at any angle from 0 to ___ degrees. - Answer-45 
 
To set the angle of a miter, position the ___ according to a scale. - Answer-Turntable 
 
The plastic or fiberboard piece located in the center of the turntable that minimizes the gap between the side of the blade and the turntable is a(n) ___. (2 words) - Answer-Kerf Board 
 
To operate a sliding compound miter saw, ...
-
Woodshop 2 Exam Questions with Correct Answers
- Exam (elaborations) • 3 pages • 2024
-
- $8.99
- + learn more
Woodshop 2 Exam 
Questions with 
Correct Answers 
 
(MITER SAW) Before turning on the ______, check that all cords are out of the way and 
locking devices are tightened. - Answer-motor 
(MITER SAW) ______ must be held firmly against the table and fence before starting up 
the saw. The ends of long boards must be supported level with the table. - AnswerStock 
(MITER SAW) Do not move the _____ _____ to see the blade. - Answer-Blade guard 
(MITER SAW) Make sure the stock will not bind in the ____ d...
-
Woodshop Safety Exam Questions And Answers
- Exam (elaborations) • 6 pages • 2023
-
Available in package deal
-
- $9.99
- + learn more
Woodshop Safety Exam Questions And Answers 
 
Safety instructions must be given before you are allowed to work on or operate any machine or ______. - ANSWER- tool 
 
You are not permitted to work on any equipment or machine if the ________ is not present. - ANSWER- teacher 
 
Guards and safety devices must be on all machines during ______. - ANSWER- operation 
 
Machinery must not be oiled or adjusted while in ______. - ANSWER- use 
 
A machine must be started and stopped only by the ______. - A...
-
Woodshop Final Exam Questions And Answers
- Exam (elaborations) • 6 pages • 2023
-
Available in package deal
-
- $11.29
- + learn more
Woodshop Final Exam Questions And Answers 
 
Hardwood lumber is commonly sold by the - ANSWER board foot 
 
Softwood comes from the evergreen or needle-bearing trees that are called - ANSWER conifers 
 
The best grade for hardwood lumber is - ANSWER FAS 
 
A standard size sheet of plywood is - ANSWER 4x8 
 
This type of plane is 14 inches long with a 2-inch cutter, and is a general-purpose plane - ANSWER jack plane 
 
A ___ joint is easy to make but not as strong as many other joi...
-
Woodshop Final Exam Review 2024
- Exam (elaborations) • 1 pages • 2024
- Available in package deal
-
- $8.99
- + learn more
Woodshop Final Exam Review 2024 
Margin of Safety: Table Saw -Answer-4" 
Margin of Safety: Radial Arm Saw -Answer-6" 
Margin of Safety: Band Saw -Answer-2" 
Margin of Safety: Jointer -Answer-4" 
Margin of Safety: Planer -Answer-N/A 
Margin of Safety: Sanders -Answer-N/A 
Margin of Safety: Chop Saw -Answer-4" 
How to square a board: -Answer-1. Joint one edge 
2. Rip board to desired width 
3. Trim one end 
4. Measure cut opposite end to desired length 
Board feet (all inches) -Answer-T"xW"...
That summary you just bought made someone very happy. Also get paid weekly? Sell your study resources on Stuvia! Discover all about earning on Stuvia