Solid mechanic - Study guides, Class notes & Summaries

HEAVY TRUCK STEERING AND SUSPENSION MICHIGAN MECHANIC STUDY GUIDE EXAM QUESTIONS AND ANSWERS You have replaced a power steering pump which failed. what should you do before putting the truck back into service? - answera. replace the hydraulic lines. b. remove air with a pressure bleeder. (not correct awnser) c. flush the system with clean power steering fluid. (possible correct awnser) d. all of the above. (not correct awnser) in the tandem setup shown below, rubber bushings would be fo...

1. When teeth are broken Answer: When would a mechanic be required to replace an escalator comb or comb plate? 2. 2" Answer: You are ordering wood planking to provide overhead protection for a temporary working platform. At minimum, how thick must the wood be? 3. Three-wire Answer: You are asked to install additional lighting in the hoistway. What type of extension cord should you use? 4. 3 feet Answer: Refer to the Figure. An apprentice is setting up a ladder to access 12 feet above his...

When you take a road test for a driver's license: 1. You must provide the vehicle. 2. The vehicle must be in safe operating condition free of safety defects. 3. You must be accompanied to the testing station by a licensed driver. 4. All of the above. Answer(15) 4 When you change your address you must notify the County Examiner of drivers: 1. In writing, within 30 days. 2. In writing, within 10 days. 3. In person, within 10 days. 4. By telephone, within 30 days. Answer(16) 1 When you ...

What is the function of a vortex generator? It is designed to delay or prevent separation of the boundary layer. What are the three axes of an airplane? Longitudinal. lateral. and vertical. Brainpower Read More Previous Play Next Rewind 10 seconds Move forward 10 seconds Unmute 0:00 / 0:15 Full screen What are the three primary flight controls of an aircraft? The ailerons. elevator. and rudder. Name several secondary flight controls and describe their genera...

HEAVY TRUCK STEERING AND SUSPENSION MICHIGAN MECHANIC STUDY GUIDE WITH COMPLETE SOLUTIONS YOU HAVE REPLACED A POWER STEERING PUMP WHICH FAILED. WHAT SHOULD YOU DO BEFORE PUTTING THE TRUCK BACK INTO SERVICE? - Correct Answer ️️ -A. REPLACE THE HYDRAULIC LINES. B. REMOVE AIR WITH A PRESSURE BLEEDER. (NOT CORRECT AWNSER) C. FLUSH THE SYSTEM WITH CLEAN POWER STEERING FLUID. (POSSIBLE CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORRECT AWNSER) IN THE TANDEM SETUP SHOWN BELOW, RUBBER BUSHI...

What is the function of a vortex generator it is used to delay or prevent the separation of the boundary layer What are the 3 axes of an airplane longitudinal, lateral and vertical Brainpower Read More Previous Play Next Rewind 10 seconds Move forward 10 seconds Unmute 0:00 / 0:15 Full screen What are the 3 primary flight controls of an aircraft ailerons, rudder, elevator Name several secondary flight controls and describe their general purpose secondary fl...

Describe passivation - ANSWER-Passivation is the formation of a protective oxide Film on the surface reducing its chemical activity and its ability to corrode Describe the following factors and how they affect corrosion - ANSWER-Oxygen: oxygen increases the rate of corrosion temperature Temperature: corrosion usually accelerated with increasing temperature Chemical salts: increase the rate of corrosion by increasing the efficiency of the electrolyte humidity: the wetter the environment,...

What is the function of a vortex generator? It is designed to delay of prevent separation of the boundary layer. What are the three axes of an airplane? Longitudinal, lateral, and vertical. What are the three primary flight controls of an aircraft? The ailerons, elevators, and rudder. Name several secondary flight controls and describe their general purpose? Secondary flight controls consist of various types of trim tabs such as balance tabs, anti-servo and servo tabs,...

Solid Mechanics (SMS) Investigate The Behaviour Of Loaded Beams

Elevator Mechanic Exam Review Questions And Answers 100% Verified. A contractor wants to raise the car speed from 100fpm to 125fpm, it currently has a 12" sheave. What sheave is required? - correct answer. Diam=12" 12/4=3" 25fpm=3" 100fpm + 25fpm= 12"+3"= 15" sheave A MOV (Metal Oxide Varistor) burns out. You replace it, but cannot read voltage or resistance. What should you do? - correct answer. Replace it with a larger MOV On a Ward-Leonard cir...