Oxyfuel cutting - Study guides, Class notes & Summaries

Module 29101-15 Welding Safety Study Guide Exam 2024. Which of these modern methods use a flux-coated consumable welding rod? A. SMAW B. GTAW C. FCAW D. GMAW A. SMAW In which of these processes is acetylene used? A. Gas tungsten arcwelding B. Carbon arc cutting C. Flux score arcwelding D. Oxy fuel cutting D. Oxy fuel cutting In the oxyfuel cutting process, which of the following is used as a fuel gas? A. Oxygen B. Propane C. Nitrogen D. Argon B. Propane

NCCER Welding Level 1 Module 2 Question and answers 2023/2024 verified to passferrous metals - correct answer What use is oxyfuel cutting best suited for? oxidize - correct answer The stream of high pressure cutting oxygen that is directed from an oxyfuel torch causes to metal to instantly _____? 3-6 - correct answer The recommended range of tinting for either the face shield or the safety glass lenses used during an oxyfuel cutting operation is ______? Oxyfuel gas welding o...

From the following list check off those which are dimensional faults prior to welding: A) Incorrect root openings B) insufficient leg C) Overlap D) Incorrect root face E) Incorrect bevel angles F) Insufficient throat A) Incorrect root openings, D) Incorrect root face E) Incorrect bevel angles Working with CSA Standard W59 or AWS D1.1 a groove angle specified on a drawing as 60 degree is required to be between (a) 45 - 60 degree (b) 55 - 70 degree (c) 55 - 65 degree (d) 60 ...

NCCER Welding Level 1 Module 2 Question and answers 2023/2024 verified to passferrous metals - correct answer What use is oxyfuel cutting best suited for? oxidize - correct answer The stream of high pressure cutting oxygen that is directed from an oxyfuel torch causes to metal to instantly _____? 3-6 - correct answer The recommended range of tinting for either the face shield or the safety glass lenses used during an oxyfuel cutting operation is ______? Oxyfuel gas welding ...

NCCER MILLWRIGHT PRACTICE EXAM 2 QUESTIONS & ANSWERS 100% ACCURATE. unusual - ANSWER-If the seal was not properly aligned or there is excessive wear in some bearing or shaft,_______ wear tracks will be the indicator sharpened brass putty knife - ANSWER-For removing hard to remove gasket materials found on sealing surfaces, ______ is recommended Conducted on the job - ANSWER-Apprenticeship training is_______ distance - ANSWER-Charting alignment on a graph requires a chart that is divided int...

NCCER 29105 Base Metal Prep Final Exam Test 2024. Welding Code A detailed listing of rules and principals applyed to welding is Requires half the weld material Compared to a single V- groove, A double V- groove weld Slower Mechanical joint preparation is _____ than thermal joint preparation Porosity The most common defect caused by surface contamination is Thermal Oxyfuel, plasma arc, or carbon arc cutting is known as what All metals should be cleaned before weldi...

Welding Module 5 – Review Exam Questions With Verified And Updated Answers. Nibblers prepare the edge of base metals using a __________________________. - answerreciprocating punch One of the joints used with a plug and slot weld is a _________________________. - answerlap Common-grade stainless steels normally contain at least ________________________. - answer11 percent chromium Surfacing welds can be used to ______________________. - answerbuild up surfaces Cutting metal with oxyf...

Second degree burn - A burn that causes the skin to blister is referred to as a: Flow meter - The amount of inert gas is controlled by the 7 3/4 - Subtract: 7 2/3 - 9 11/12 151' - A boilermaker mechanic needs 12 lengths of 1/4" membrane. Each length is to 12'7". What is the total length of membrane needed? 31' 2" - A welder needs tube sections (Dutchmen) in the following lengths: 8'10", 12' 5", and 9' 11". What is the total amount of tubing needed? 19" - Add: 1/4 +11/12+5/6+1...

Boilermaker NCCER exam with questions & veried answers 2023/2024 latest update WHEN SHOULD RIGGING MATERIAL BE ATTACHED TO A BEAM TIIAT IS BEING DEMOLISHED? BEFORE ANY BOLTS ARE REMOVED OR ANY CUTTING IS DONE ON THE BEAM WHICH TYPE OF INSOLATION IS REQUIRED BEFORE A VESSEL IS ENTERED? DocING, TAGGING, AND BLINDING LINES THAT FEED THE VESSEL ACCORDING TO OSHA OXVGEN AND ACETYLE CYLINDERS IN STORAGE MUST BE SEPARATED WHAT NUMUM 20ft WHAT IS THE FIRST THING A BOILER MAKER SHOULD DO SEFORE CU...

Module 29101-15 Welding Safety Study GuideWhich of these modern methods use a flux-coated consumable welding rod? A. SMAW B. GTAW C. FCAW D. GMAW A. SMAW In which of these processes is acetylene used? A. Gas tungsten arcwelding B. Carbon arc cutting C. Flux score arcwelding D. Oxy fuel cutting D. Oxy fuel cutting In the oxyfuel cutting process, which of the following is used as a fuel gas? A. Oxygen B. Propane C. Nitrogen D. Argon B. Propane Apprenticeship programs ...