Ospf router - Study guides, Class notes & Summaries

OSPF Test: Questions and Answers 100% Solved Cost Correct answer Which interface configuration command might you use as an alternative to using the bandwidth command and achieve the same goal when implementing OSPF? To ensure that OSPF uses a suitable value when calculating its metric Correct answer Why would you use the bandwidth command when configuring an interface where OSPF routing is used? EIGRP Correct answer If a Cisco router learns two routes to the same destination, one t...

OSPF Exam; Questions and Answers 100% Solved OSPF uses the protocol number ___________ for its inter-router communication. a. 87 b. 88 c. 89 d. 90 Correct answer 89 OSPF uses ___________ packet types for inter-router communication. a. three b. four c. fi ve d. six e. seven Correct answer fi ve

Cisco CCNA Test 2 Questions and Answers If all OSPF routers in a single area are configured with the same priority value, what value does a router use for the OSPF router ID in the absence of a loopback interface? - Answer-A. the IP address of the first Fast Ethernet interface B. the IP address of the console management interface C. the highest IP address among its active interfaces D. the lowest IP address among its active interfaces E. the priority value until a loopback interface is co...

Advanced OSPF Chapter 9 Concepts: Questions and Answers 100% Solved Router B1, an internal router in area 1, displays the following output. The only two ABRs connected to area 1 are performing Type 3 LSA filtering. Which of the following answers is true based on the information in the output from B1? R1# show ip route 10.1.0.0 255.255.0.0 longer-prefixes ! Legend lines omitted for brevity 10.0.0.0/8 is variably subnetted, 17 subnets, 3 masks O 10.1.2.0/24 [110/658] via 10.10.13.1, 00...

ITEC 1025 Module 3 Exam with Verified Answers A Layer 3 switch typically routes traffic quicker than a traditional router. False, The fundamental difference between a router and a Layer 3 switch is that Layer 3 switches have optimized hardware to pass data as fast as Layer 2 switches, yet they make decisions on how to transmit traffic at Layer 3, just like a router. Within the LAN environment, a Layer 3 switch is usually faster than a router because it is built on switching hardware. ...

CCNA OSPF QUESTIONS WITH CORRECT ANSWERS Why are link-state protocols the only type of IGP found in large network environments? They support fast convergence with support for scalability and multivendor environments What type of routing protocol is OSPF? Link-state What are the advantages of link-state protocols over distance vector protocols? - More scalable - Each router has a full picture of the topology - Updates are sent when there is a topology change and periodically ...

Disadvantage of NAT - Answer-No end to end addressing. How to re-enable the port without disrupting network operation - Answer-Issues the shutdown command followed by the no shutdown command on the interface. What is the purpose of the startup configuration file on a Cisco router - Answer-To contain the commands that are used to initially configure a router on startup. An STP cable uses what type of connector - Answer-RJ-45. A router in an OSPF enterprise network has a default static...

WGU 802 Comprehensive Exam (2024) || All Questions & Answers (100% Accurate) WGU 802 Comprehensive Exam (2024) || All Questions & Answers (100% Accurate) A network is experiencing a number of CRC errors during normal network communication. At which of the following layers of the OS model will the administrator MOST likely start to troubleshoot? A. Layer 1 B. Laver 2 C. Layer 3 D. Layer 4 E. Layer 5 F. Layer 6 G. Layer 7 - ANSWER - Layer 1 A branch of a company recently switched to...

What are the console settings for out-of-band (OOB) - Answer The switches use default settings for the terminal emulation software: •9600 bps •8 data bits •No parity •1 stop bit •No flow control Switch modules come in two forms. Which switch forms supports port name "a39"? - Answer Module Switch come in fix and module. Modular switches support alphanumeric naming i.e. interface <slot_letter><1-24> What aos command will allow you to configure ports 1, and 4 thr...

TESTOUT EXAM 1 QUESTIONS AND ANSWERS 100% PASS Routing data between computers on a network requires several mappings between different addresses. Which of the following statements is true? Routers uses ARP to resolve known IP addresses into MAC addresses by broadcasting requests to the network. Used to get the IP address of a host from a known MAC address RARP & BOOTP Used to transfer files TFTP & FTP Used to identify routes through an internetwork OSPF & RIP The serial 0/1/0...