Hydraulics pneumatics - Study guides, Class notes & Summaries

Pascal's Law deals with measuring the amount of force that acts on a unit of area. The formula we use to express this is: - ️️F=A x D Volume is the amount of space a fluid occupies. The formula we use to express this is: - ️️V=A x D A gain in mechanical advantage is achieved using: - ️️Different sized pistons and constant pressure Viscosity is - ️️The internal resistance to flow The flash point is the temperature at which a liquid gives off vapor in sufficient quanti...

MSSC MAINTENANCE PNEUMATICS Questions WITH VERIFIED 100% CORRECT ANSWERS Which are considered a fluid system, pneumatics or hydraulics? - ANSWER Both are considered fluid systems What are the two types of conductors used in a pneumatic system? - ANSWER Supply line and actuator line The S.I. unit for pressure is? - ANSWER kPa What is the maximum pressure that the gauge shown can measure? - ANSWER 7000 kPa What value is shown on the gauge? - ANSWER 56 psi To convert gauge pres...

Pneumatics - ️️The use of a gas flowing under pressure to transmit power from one location to another. Pneumatic systems - ️️Use a compressible gas Pneumatic systems - ️️Posses a quicker, jumpier motion Pneumatic systems - ️️Are not precise; are not easily controllable Pneumatic systems - ️️Require a lubricant Pneumatic systems - ️️Are generally cleaner Pneumatic systems - ️️Often operate at pressures around 100 psi Pneumatic systems - ️️Gener...

Using a hand pump, pressure of 100 PSI has been built up in a hydraulic system. The hand pump piston is 1 inch in diameter. A 1/2-inch line connects the hand pump to an actuating cylinder 2 inches in diameter. What is the pressure in the line between the hand pump and the actuator? - ️️100 PSI. A common cause of slow actuation of hydraulic components is - ️️internal leakage in the actuating unit. In a hydraulic system that has a reservoir pressurized with turbine-engine compressor ...

pilot line correct answer: A dashed line in a pneumatic schematic diagram represents a(n)... A positive displacement air compressor... correct answer: produces a new volume of air for every stroke An accumulator is a hydraulic component that... correct answer: stores fluid under pressure At a given flow rate, a cylinder retracts faster than it extends because... correct answer: the rod takes up space Before disconnecting oil lines, correct answer: lockout/tagout equipment Com...

the fluid conditioning system of hydraulic powered equipment provides fluid that is clean and maintained in an acceptable operating ___________. - ️️Conditions What are three components that contribute to contaminants in the hydraulic fluid as they wear? - ️️Water, air , heat ________ percent or more of the prime mover horsepower is converted into heat that raises fluid temperature in a hydraulic system? - ️️20 what is the best approach to assure a clean operating system? - ...

Incident Safety Officer Exam Questions With 100% Correct Answers 2024/2025 Individual turbine blades can be __ to __ feet long creating a rotational diameter and danger zone of more than ___ feet 60 to 130/300 a ___ is defined in writing and can take on many forms:SOPS, SOGS, departmental directives, temporary memorandums formal process Procedures Strict directives that must be followed with little or no flexibility An ___ is a process or operation that is part of a department...

An automobile traces 10 miles in 15 minutes - 40 A 12 tooth sprocket and a 60 tooth sprocket are connected by a chain. - Counterclockwise If the ramp is inclined 30 degrees and the friction of the ramp is 0.25 - 284 A torque of 15 feet is the result when ______ acts on a 6 in wrench - 30 Formula for pressure - force/area 12 tooth gear is meshed with a 60 tooth gear - 25:1 Raise the arm of a robot, last of 6 gears must rotate clockwise - Counterclockwise A torque of 30 ft*lbs is the result...

Jig - A device that holds and locates a piece of work and guides the tools that operate upon it. Example: table, anything that is used to guide material. Fixture - A device designed and built for holding a particular piece of work for machining operations without the ability to guide tools Postprocessor - A post-processor is in essence software and or a sequence of instructions to deal with a nuetral format generated by a CAM system and translates that nuetral language to one that makes yo...

Torches are designed to avoid mixing oxygen and acetylene by using __________. Reverse-flow check valves at torch inlets or regulator outlets To prevent leakage around the valve during use, __________ An oxygen cylinder valve should be opened all the way An explosion can occur if __________ comes in contact with oil. High pressure oxygen A green welding hose normally indicates that this hose carries __________. Oxygen A __________ is a non-destructive test that us...