Asme code questions 2023 Study guides, Class notes & Summaries

ASME code of ethics questions and Answers 2023 1. engineers prioritize the _________, _________, and _________ of the public when performing their professional duties safety, health, welfare 2. engineers shall perform services only in the areas of their __________. competence 3. Engineers shall continue their _________________ throughout their careers and shall provide opportunities for the _________ and ____________________ of those engineers under their supervision profession...

GDTP ASME Y14.5M 1.4 Fundamental Rules Questions and Answers 2023 Fundamental Rules Dimensioning and tolerancing shall clearly define engineering intent and shall conform to the following: 1.4 a) Each dimension shall have a tolerance, except for those dimensions specifically identified as reference, maximum, minimum, or stock (commercial stock size). 1.4 b) Dimensioning and tolerancing shall be complete so there is full understanding of the characteristics of each feature. ...

NEIEP 120/130 Multi Questions Answered 2023 When teeth are broken When would a mechanic be required to replace an escalator comb or comb plate? 2" You are ordering wood planking to provide overhead protection for a temporary working platform. At minimum, how thick must the wood be? Three-wire You are asked to install additional lighting in the hoistway. What type of extension cord should you use? 3 feet Refer to the Figure. An apprentice is setting up a ladder to acces...

Mechanic Review Questions and Answers 2023 SDS What is the best source for determining if a solvent is safe or not? 5 feet A ladder needs to be extended 20 feet from the ground floor to the next landing, how far from the wall should the base of the ladder be? operate the bottom hoistway access switch which procedure would you use to get into a pit to service an elevators oil buffer? pit switch and light switch When you are installing pit equipment, which two items are r...

NEIEP 200 Final Review Questions and Answers, latest 2023 Which lay of wire rope has the strand wires in line with the rope axis? Regular Lay At what speed should the counterweight safeties be set to trip? Up to 10% higher than the car governor Which type of safety uses an oil buffer between the car and safety planks? Type C What is the purpose of the terminal motion switch? slow down and stop the car automatically at or near the top or bottom landing If you have...

WLD 112 final exam questions and answers 2023 with complete solution The V-shaped head attachment of a combination square can be used to locate the center of shafts or other round objects The tool uses a bubble in a glass vial to check level and plumb is a level Internal misalignment between two sections of pipe to be welded end-to-end is checked using a Hi-Lo gauge When using a chain to lift or lower weldment parts, always secure the chain fall to an overhead structural member with an ...

ASME Code questions 2023 Questions and Answers You must operate boilers that burn various fuels. From the image below, what type of fuel system is indicated? the image shown a fuel-oil burner arrangement. The maintenance of automatic direct fired boilers is covered under what document? ASME CSD-1 The various license classifications and grades for operating high pressure boilers are found in the NJAC reference section listed as: Table 3.4 Who is responsible for obtaining...

codes unit 4 Questions and Answers 2023 ASME VI warns that if abnormal conditions occurs, the operator should shut down the boiler immediately and close the ________ valves main and pilot test firing valves ASME CSD-1 recommends testing of the combustion air proving switch: monthly In case of case of a single boiler steam heating system, ASME VI advises operators to warm up heating boilers and their piping simultaneously To protect the safety relief valve, the normal hot...

ASME intro Questions and Answers 2023 CSA Canadian Standards Association Develops standards in 57 areas. Has created standards relating to heating boiler equipment. Publishes standards in print and electronic form and provides training and advisory services. Is composed of representatives from industry, government, and consumer groups. Most standards are voluntary, meaning there are no laws requiring their application. Unless they are adopted by a jurisdiction. The two CS...

WLD 112 final exam questions and answers 2023 with complete solution The V-shaped head attachment of a combination square can be used to locate the center of shafts or other round objects The tool uses a bubble in a glass vial to check level and plumb is a level Internal misalignment between two sections of pipe to be welded end-to-end is checked using a Hi-Lo gauge When using a chain to lift or lower weldment parts, always secure the chain fall to an overhead structural member with an ...