Ospf router - Study guides, Class notes & Summaries

OSPF Chapter 9 (Single-Area OSPF); Questions and Answers 100% Solved The OSPF hello timer has been set to 15 seconds on a router in a point-to-point network. By default, what is the dead interval on this router? Correct answer 60 seconds - By default, the dead interval is calculated as 4 times the hello interval. At which OSPF state are neighbor routers converged and able to exchange routing updates? Correct answer Full What are the 7 features of OSPF? Correct answer 1. AD = 110 2....

Your company is running IGRP using as AS of 10. You want to configure EIGRP on the network but want to migrate slowly to EIGRP and don't want to configure redistribution. What command would allow migration over time to EIGRP without configuring redistribution router eigrp 10 Which EIGRP information is hel in RAM and maintained through the use of Hello and update packets? Neighbor table Topology table Brainpower Read More Previous Play Next Rewind 10 seconds Move forwa...

IT120 Final Exam Questions and Answers Graded A+ Does the internet use iPv4 or iPv6? Both How do you find the value of the payload data? Total length - (base header + extension header) or Total length - base header - extension header How do you find the value of the payload length field? Total length - base header How long is an iPv6 address? 128 bits How many IP addresses should a router have? Two or more Is BGP an exterior or interior routing protocol? Exterior Is OSP...

How is the process of summarizing routes on an OSPF router accomplished? a. By using the interface confi guration command summary-address network prefi x-length b. By using the OSPF process confi guration command summary-address network prefi x-length c. By using the OSPF process confi guration command area area-id range network subnet-mask d. By using the interface confi guration command area area-id summary-address network subnet-mask - By using the OSPF process confi guration command are...

NSE 7 - Enterprise Firewalls 6.2: Questions and answers, rated A+ What are the advantages of using OSPF? Scalable to larger networks Faster convergence than distance-vector routing protocols Relatively quiet during steady-state conditions 30-minute refresh or when updates are sent due to changes made What are the disadvantages of using OSPF? May require planning and tuning to optimize performance May be difficult to troubleshoot in large networks Brainpower Read More What is LSDB? ...

After OSPFv3 has been enabled on a router. You need to set the router ID. Which command will accomplish this task? - router-id [ID number] If you have multiple IPv6 address prefixes on a single OSPF interface, which of the following statements are true? (Select two.) - All address prefixes on an interface are included by default. Users cannot select some address prefixes to be imported into OSPF for IPv6; either all address prefixes on an interface are imported, or no address prefixes on an...

NWC203 FE Guaranteed Success Q.24 The DNS protocol runs over and uses port A HTTP 53 B. TCP 51 C. UDP 51 D. TCP 52 E. UDP. 53 E Q1-In TCP congestion control, two important variables the sender has to keep track area. A.Congestion window and the threshold. B.Congestion window and socket number. C.Threshold and Receiving windowd. D.MSS and RTT A Q2-The physical layer of the receiving device passes bits up to which higher level layer? A. application B. presentaiton ...

You are a network administrator configuring OSPF and EIGRP in your enterprise. One of your routers is receiving an OSPF route to a subnet through more than one path. One route is a redistributed route coming from a Not-So-Stubby-Area and another is coming directly from an adjacent EIGRP Router. Only the external link cost has been set to feed into the Shortest Path First calculations. Which route type will be the one most likely to enter the routing table? - E2 You are a network administrat...

CCIE Exam Questions & Answers 2023/2024 What does the EIGRP K5 value modify? - ANSWER-MTU What is an OTV edge device? - ANSWER-Connects a site to the overlay network What is the purpose of the command ppp microcode? - ANSWER-Enables hardware PPP framing on an async interface. What does the EIGRP K3 value modify? - ANSWER-Delay What is a pseudowire ID FEC? - ANSWER-Always set to 128. What information is carried in the community attribute when OSPF is used between PE and CE? - ...

CCNP/CCIE ENCOR "Do I know this Already?" - Chapters 8/9/10 Chapter 8 - OSPF - ANSWER-"Do I know this Already?" ---> OSPF uses the protocol number ___________ for its inter-router communication. a. 87 b. 88 c. 89 d. 90 - ANSWER-C - 89 OSPF uses ___________ packet types for inter-router communication. a. three b. four c. five d. six e. seven - ANSWER-C - Five What destination addresses does OSPF use, when feasible? (Choose two.) a. IP address 224.0.0.5 b. IP ...