Camber - Study guides, Class notes & Summaries

ASE A4 practice test questions and answers 100% pass 2. A driver says that the front end of his car vibrates up and down while traveling at most road speeds. Tech A says that too much runout of the front wheels could be the cause. Tech B says that a static out of balance of the front wheels could be the cause. Who is right? A. Tech A only B. Tech B only C. Both A and B D. Neither A or B - Answer ️️ -C. Both Techs are right. Too much runout or static out of balance in the front wheels...

ASE A4 practice test Questions and answers |100% pass 2. A driver says that the front end of his car vibrates up and down while traveling at most road speeds. Tech A says that too much runout of the front wheels could be the cause. Tech B says that a static out of balance of the front wheels could be the cause. Who is right? A. Tech A only B. Tech B only C. Both A and B D. Neither A or B - Answer-C. Both Techs are right. Too much runout or static out of balance in the front wheels will ...

SOLVED - Elaborated ASE A4 ASE SUSPENSION & STEERING Exam 1 for 2023 Ace in your ExamsProf.Exams ASE A4 ASE SUSPENSION & STEERING Exam 1 for 2023 Ace in your Exams in 1 attempt! 1. A driver says that the front end of his car vibrates up and down while traveling at most road speeds. Tech A says that too much runout of the front wheels could be the cause. Tech B says that a static out of balance of the front wheels could be the cause. Who is right? A. Tech A only B. Tech B only C. Both A a...

Which of the following is the correct way to adjust tapered roller bearings? A. Torque and the back off OEM specification B. Torque to OEM specification C. Adjust to a minimum of .150 " (3.80mm) end-play. D. Torque to 50 ft lbs. (Ans- Torque and then back off OEM specification. It is typical to torque the bearing while rotating the wheel and then back off the nut a certain amount. A vehicle has a crooked steering wheel when driving down the road. Technician A says this could be caus...

Flight Mechanics Past Questions with Complete Solutions Which force opposes an aircraft’s motion through the air? A) Lift B) Thrust C) Gravity D) Drag D) Drag What happens to the stall speed as the aircraft’s weight increases? A) Stall speed decreases B) Stall speed remains the same C) Stall speed increases D) Weight does not affect stall speed C) Stall speed increases What is the primary function of the rudder in an aircraft? A) Control roll 2 B) Control pitch ...

HEAVY TRUCK STEERING AND SUSPENSION MICHIGAN MECHANIC STUDY GUIDE RATED A+ YOU HAVE REPLACED A POWER STEERING PUMP WHICH FAILED. WHAT SHOULD YOU DO BEFORE PUTTING THE TRUCK BACK INTO SERVICE? A. REPLACE THE HYDRAULIC LINES. B. REMOVE AIR WITH A PRESSURE BLEEDER. (NOT CORRECT AWNSER) C. FLUSH THE SYSTEM WITH CLEAN POWER STEERING FLUID. (POSSIBLE CORRECT AWNSER) D. ALL OF THE ABOVE. (NOT CORRECT AWNSER) IN THE TANDEM SETUP SHOWN BELOW, RUBBER BUSHINGS WOULD BE FOUND AT: A. POINT...

Cambridge International As and A Level CHEMISTRY 9701/43 Paper 4 A Level Structured Questions October/November 2023

Cambridge International As and A Level ECONOMICS 9709/11 Paper 1 A Level Structured Questions QUESTION PAPER & MARKING SCHEME/ [MERGED] October/November 2023

A driver says that the front end of his car vibrates up and down while traveling at most road speeds. Technician A says that too much runout of the front wheels could be the cause. Technician B says that static out-of-balance of the front wheels could be the cause. Who is right? A. Technician A only B. Technician B only C. Both A and B D. Neither A of B - Answer-The correct answer is C, both technicians are right. Too much runout or static out-of-balance in the front wheels will cause a vibr...

A vehicle is brought in with a bent subframe. Technician A says to section the subframe. Technician B says the subframe should not be repaired and must be replaced. Who is right? A, B, Both, or Neither - Answer-Technician B only The subframe should never be sectioned, and should rarely, if ever, be worked. It is typically a bolt-on part that does not lend itself to traditional straightening methods. Vehicle manufacturers recommend replacement. The first step in bleeding brakes is to: A. c...