100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
2024 Michigan Mechanical Code Exam Q’s and A’s $12.49   Add to cart

Exam (elaborations)

2024 Michigan Mechanical Code Exam Q’s and A’s

 0 view  0 purchase
  • Course
  • 2024 Michigan Mechanical Code
  • Institution
  • 2024 Michigan Mechanical Code

2024 Michigan Mechanical Code Exam Q’s and A’s

Preview 2 out of 8  pages

  • November 20, 2024
  • 8
  • 2024/2025
  • Exam (elaborations)
  • Questions & answers
  • 2024 Michigan Mechanical Code
  • 2024 Michigan Mechanical Code
avatar-seller
Nursephil2023
2024 Michigan Mechanical Code
Exam Q’s and A’s
Welded - -A mechanical joint is not ________ .

- make up air - -Any combination of outdoor and transfer air intended to
replace exhaust air and exfiltration is ___________.

- duct - -A tube or conduit utilized for conveying air is a ___________ .

- press joint - -A permanent mechanical joint incorporating an elastomeric
seal and corrosion resistant grip ring is a __________ .

- third party certified - -Plastic pipe, fittings and components shall be
___________ as conforming to NSF 14.

- replaced - -Defective material or parts shall be ___________ or repaired in
such a manner to preserve its original listing.

- 25 - -In bearing partitions, wood studs shall not be cut or notched to a
depth exceeding __________ % of its depth.

- 18, listed - -Equipment with an ignition source shall be elevated such that
the ignition source is not less than __________ inches above the garage floor
unless the appliance is _________ as flammable vapor ignition resistant.

- 6 - -Equipment shall be suspended a minimum of ________ inches above
the adjoining grade.

- 22 - -Attics containing appliances shall be provided with an opening and
unobstructed passageway not less than _________ inches wide.

- 16, 30 - -Equipment on elevated structures or roofs above __________ feet
requiring access must be provided with an interior or exterior access that
does not require climbing over obstructions ________ inches high.

- R-3 occupancies - -Providing permanent access to equipment on a roof
does not apply to ____________ .

- 12 - -The clearance reduction methods shown in 308.4.2 shall not be used
to reduce the clearance of solid fuel burning appliances any less than
_________ inches.

, - 10 - -Outdoor intake and exhaust openings shall be located a minimum of
_________ feet from lot lines or buildings on the same lot.

- 100 - -Variable air volume boxes shall be designed to regulate outdoor air
unless they provide _________ % of outdoor air.

- 25 - -Mechanical ventilation systems for enclosed parking garages are not
required to operate continuously when a carbon monoxide detector is
installed until the level reaches ________ ppm.

- manual or automatic - -Mechanical ventilation systems shall be provided
with ________ controls that will operate the system whenever the spaces are
occupied.

- 0.02 - -The mechanical exhaust rate for a crawl space shall be not less
than ___________ cfm per square foot of horizontal area.

- 60 - -Crawl space ventilation must be a minimum 0.02 cfm per square foot
and shall be automatically controlled to operate when the humidity exceeds
___________ %

- outdoors, nuisance - -The air removed by every exhaust system shall be
discharged _____________ and at a point where it will not cause a ____________.

- whole house ventilation type - -Only _________ fans can discharge their
exhaust into the attic of dwelling units that have private attics.

- 6 - -Flammable finish exhaust duct terminations shall be a minimum
___________ feet from exterior walls and roofs.

- 1 - -The exhaust rate for hazardous materials stored in excess of the
maximum allowable quantity shall be provided at a rate of not less than
__________ cfm/ft2 of the storage floor area.

- 200 - -Clothes dryers exhausting more than ________ cfm requires make up
air.

- 35 - -The maximum length of a clothes dryer duct is ___________.

- outside of the airstream - -Commercial type clothes dryers require the fan
motors be located ____________.

- 18 - -The grease duct clearance required when located within a shaft
enclosure is _________ inches to the combustible construction.

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller Nursephil2023. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for $12.49. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

72042 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy study notes for 14 years now

Start selling
$12.49
  • (0)
  Add to cart