HVAC/R Gas Heat Module Final Exam Study Guide QUESTION AND ANSWERS 100% CORRECT (26 PGS)
2 views 0 purchase
Course
INIWIC
Institution
INIWIC
HVAC/R Gas Heat Module Final Exam Study Guide QUESTION AND ANSWERS 100% CORRECT (26 PGS) The range between the highest and the lowest room temperature controlled by the thermostat, is defined as........ - correct answer The temperature swing
The two-stage thermostat heating terminal that is ju...
HVAC/R Gas Heat Module Final Exam
Study Guide QUESTION AND ANSWERS
100% CORRECT (26 PGS)
The range between the highest and the lowest room temperature controlled
by the thermostat, is defined as........ - correct answer ✔The temperature
swing
The two-stage thermostat heating terminal that is jumpered to RC is..... -
correct answer ✔Terminal RH
Which of the following is TRUE of the fan switch? - correct answer ✔Modern
fan switches cycle the fan based on time.
What is a draft pressure switch? - correct answer ✔A switch that senses
when the vent is in a draft condition.
What is the purpose of the limit switch? - correct answer ✔It prevents
overheating by interrupting the circuit to the gas valve.
How is the limit wired on a furnace that uses a line voltage limit? - correct
answer ✔The limit is wired in series with the transformer primary.
The main limit shuts the gas valve down when.... - correct answer ✔The heat
exchanger area becomes overheated.
What does a roll-out switch do? - correct answer ✔It shuts off the gas valve if
flames are sensed outside the combustion area.
,What is the purpose of a flame-proving device in a system with a standing
pilot? - correct answer ✔It shuts off the gas flow in case the pilot goes out.
How many volts are sent to a furnace spark igniter? - correct answer
✔10,000 V
What is an intermittent pilot ignition system? - correct answer ✔The gas pilot
is ignited with each call for heat and shuts off at the end of the call.
How does the flame rod sense the flames in a flame rectification circuit? -
correct answer ✔The flame changes the AC voltage to pulsed DC current.
Why should the heating element of a hot-surface igniter NOT be touched
when installing a replacement igniter? - correct answer ✔The igniter will burn
out where you touch it.
The burner assembly and furnace cabinet should be grounded for safety and
because....... - correct answer ✔Most control boards for direct spark ignition
or hot surface igniters will not operate correctly unless the unit is grounded.
Hot-surface igniters typically operate on....... - correct answer ✔120 V
Some furnaces use two automatic shutoffs that are mechanically in series to
provide additional safety. What type of valves are these? - correct answer
✔Redundant Valves
Why do direct spark ignition furnaces and hot-surface ignition furnaces require
redundant gas valves? - correct answer ✔For safety since there is no pilot
safety solenoid.
, What is a redundant gas valve? - correct answer ✔A gas valve with two
valves mechanically in series.
The operation of modern induced-draft equipment is normally controlled
by........ - correct answer ✔An electronic board
When the room-temperature setting is reached, what components are
opened? - correct answer ✔Thermostat and gas valve circuits.
In a traditional gas furnace with a standard combination gas valve, what
controls the gas valve? - correct answer ✔The heating thermostat.
What does the furnace board do on most modern furnaces? - correct answer
✔It controls the ignition, safety, and blower operation
The typical start up sequence for a hot surface ignition system is........ - correct
answer ✔Combustion blower prepurge, igniter energized after a delay, gas
valve energized after a delay, flames sensed, indoor blower energized after
time delay.
The major electrical loads in an induced-draft hot surface ignition furnace
are..... - correct answer ✔Induced-draft blower, indoor fan motor, the gas
valve, the igniter.
Two stage furnaces require..... - correct answer ✔A two-stage gas valve.
Why should the technician check the furnace door safety switch if nothing
operates? - correct answer ✔The door switch is wired into the main power
circuit.
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Academia199. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $13.99. You're not tied to anything after your purchase.
