100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
Previously searched by you
NACE CIP CBT EXAM 2 WITH QUESTIONS AND WELL-DETAILED AND VERIFIED ANSWERS || GRADED A+ | LATEST VERSION 2024 | GUARANTEED PASS | BEST VERSION$25.49
Add to cart
NACE CIP CBT EXAM 2 WITH QUESTIONS AND WELL-DETAILED AND VERIFIED ANSWERS || GRADED A+ | LATEST VERSION 2024 | GUARANTEED PASS | BEST VERSION
1 view 0 purchase
Course
NACE CIP CBT
Institution
NACE CIP CBT
NACE CIP CBT EXAM 2 WITH QUESTIONS AND
WELL-DETAILED AND VERIFIED ANSWERS ||
GRADED A+ | LATEST VERSION 2024 |
GUARANTEED PASS | BEST VERSION
Name some tests that may need to be conducted during surface preparation and
coating operations. - ANSWER-Temperature, RH, DP, Anchor Profile, Surfa...
NACE CIP CBT EXAM 2 WITH QUESTIONS AND
WELL-DETAILED AND VERIFIED ANSWERS ||
GRADED A+ | LATEST VERSION 2024 |
GUARANTEED PASS | BEST VERSION
Name some tests that may need to be conducted during surface preparation and
coating operations. - ANSWER-Temperature, RH, DP, Anchor Profile, Surface
Cleanliness
Name some of the documentation/reports that may be required to be maintained on
a coatings project. - ANSWER-Daily, weekly summary, materials usage report,
manpower and equipment, non-conformance, conformance
What are the most important characteristics of a good report? - ANSWER-
Objective, Accurate, Detailed
What is the inspector's primary responsibility and what should the inspector not do
as it pertains to the specification? - ANSWER-- enforce specification
- do not make changes
What type of information should you expect to find on a Product Data Sheet? -
ANSWER-- Surface prep and application info (i.e. recommended surface
cleanliness)
- Recommended application methods and equipment (tip sizes)
- Environmental parameters for application
,What type of information should you expect to find on a Safety Data Sheet? -
ANSWER-- Health, Safety and Environmental
- PPE required
- Physical characteristics
- Emergency responder info
Difference between QA and QC - ANSWER-QA: any systematic process of
checking to see whether a product or service being developed is meeting specific
requirements
QC: a procedure or set of procedures intended to ensure that a manufactured
product or service adheres to a defined set of quality criteria or meets the
requirements of the client or customer
Identify some of the defects that can be caused by incorrect application
temperatures - ANSWER-- failure to cure
- too rapid solvent evaporation
- poor film formation
Describe relative humidity - ANSWER-The amount of moisture in the air
compared to saturation level
What is the dew point temperature? - ANSWER-Temperature at which moisture
will begin to form on a steel surface
Name some of the effects wind may have on a coatings project - ANSWER--
blowing abrasives
,- causing excessive drift or overspray
- accelerating solvent evaporation
- contributing to the formation of dry spray
Advantages of centrifugal blast equipment include: - ANSWER-- dust and fines
are contained
- abrasives are easily recycled
- blasting and priming can be an inline operation
- general overall economy
- no compressors, piping, or air handling equipment needed for wheel blasting
The inspector checklist for surface preparation should include: - ANSWER--
ambient conditions
- conditions of the substrate
- pre-blast surface cleanliness
- shot/grit size selection
- shot/grit cleanliness
- abrasive blasting equipment
- surface profile
- surface cleanliness after blasting
- operator qualifications
- safety
Abrasive media typically used for recycling include: - ANSWER-- steel shot
- steel grit
You are on a job and observe the coating is being applied in an unacceptable
manner. As an inspector you should ____ and ____ - ANSWER-- report to the
contractor's supervisor
- report to the owner's representative
Which standard gives guidelines for how many DFT measurements should be
taken in a given area? - ANSWER-SP 2
A pre-job conference should be held - ANSWER-after bids have been submitted
and contracts signed
What are the goals of a pre-job conference? - ANSWER-- review and discuss the
scope of work
- discuss lines of communication between parties
- discuss and clarify inspector's responsibilities and authority
What is one of the inspector's roles at a pre-job conference? - ANSWER-clarify
reporting requirements
According to ASTM D 4417 Method B-2014, when taking measurements using a
profile gauge, at each location make ______ - ANSWER-ten (10) readings per
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller winnieelizabeth424. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $25.49. You're not tied to anything after your purchase.
