100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
MACHINIST MATE ACTUAL EXAM TEST BANK 500+ QUESTIONS AND WELL ELABORATED ANSWERS TOP RATED VERSION FOR ALREADY A GRADED HIGHLY RECOMMENDED BY EXPERTS | NEW AND REVISED $22.49   Add to cart

Exam (elaborations)

MACHINIST MATE ACTUAL EXAM TEST BANK 500+ QUESTIONS AND WELL ELABORATED ANSWERS TOP RATED VERSION FOR ALREADY A GRADED HIGHLY RECOMMENDED BY EXPERTS | NEW AND REVISED

 1 view  0 purchase
  • Course
  • MACHINIST MATE
  • Institution
  • MACHINIST MATE

MACHINIST MATE ACTUAL EXAM TEST BANK 500+ QUESTIONS AND WELL ELABORATED ANSWERS TOP RATED VERSION FOR ALREADY A GRADED HIGHLY RECOMMENDED BY EXPERTS | NEW AND REVISED MACHINIST MATE ACTUAL EXAM TEST BANK 500+ QUESTIONS AND WELL ELABORATED ANSWERS TOP RATED VERSION FOR ALREADY A GRADE...

[Show more]

Preview 4 out of 45  pages

  • November 1, 2024
  • 45
  • 2024/2025
  • Exam (elaborations)
  • Questions & answers
  • machinist mate
  • MACHINIST MATE
  • MACHINIST MATE
avatar-seller
2024newestexams
MACHINIST MATE ACTUAL EXAM TEST BANK 500+
QUESTIONS AND WELL ELABORATED ANSWERS TOP
RATED VERSION FOR 2024-2025 ALREADY A GRADED
HIGHLY RECOMMENDED BY EXPERTS | NEW AND
REVISED
What NSTM deals with propulsion and SSTG Turbines? - CORRECT ANSWER-NSTM 231



Whats type of rotary pump is frequently used as a lubricanting pump on pumpe and other aux
equipment? - CORRECT ANSWER-Simple gear pimp



What is the normal length of a tapered plug? - CORRECT ANSWER-3"



What is installed on a non-condensing turbone to protect turbine casing from excessive pressure? -
CORRECT ANSWER-Combination exhaust relief valve 2-3 psi above exhaust line pressure



On an SSTG, what protects turbine casing from excessive pressure? - CORRECT ANSWER-Back pressure
trip



When starting an SSTG, what is a minimum lube oil temp? - CORRECT ANSWER-60 degrees



What are the four sections of a PQS? - CORRECT ANSWER-Fundamentals, systems, watchstations, qual
card



What is the number for a PMS feedback report? - CORRECT ANSWER-4790/7B



When should oil coolers be put into operation on aux machinery? - CORRECT ANSWER-When temp of
lube oil leaving cooler is 100 degrees



DFT is designed to operate at what pressure and temp? - CORRECT ANSWER-15 psi and 240-250 degrees

,What is installed on a centrifugal pump to eliminate renewing of an entire propellor and pump casing
due to rapid wear? - CORRECT ANSWER-Wearing rings



The federal water pollution control act was amended in what year? - CORRECT ANSWER-1970



What is the NSTM for compressed air systems? - CORRECT ANSWER-551



What is the max allowable pressure drop across a fuel oil duplex strainer when online? - CORRECT
ANSWER-3%



What is the NSTM for general reduction gear? - CORRECT ANSWER-241



What is the NSTM for forced draft blowers? - CORRECT ANSWER-554



What is the required amount of sodium nitrate used for a sodium nitrate wet lay up? - CORRECT
ANSWER-10lbs per 1,000 gallons of feed water



When is the current ships maintenance project verified and updated? - CORRECT ANSWER-Monthly



PMS schedules are categorized in what manner? - CORRECT ANSWER-Cycle, quarterly, weekly



Main feed pump is classified as what type of pump? - CORRECT ANSWER-Multi stage

High speed

Turbine driven



How long must the engine room/fire room operating log be kept for? - CORRECT ANSWER-2 years



Main feed pumps are fitted with what two types of governors? - CORRECT ANSWER-Speed limiting

Constant speed

,the number of revolutions to major speed change is entered in what column? - CORRECT ANSWER-3



Entries for astern pitch are preceded by what level? - CORRECT ANSWER-B



What is the max allowable super heater outlet temp during transition periods of 15mins - 1 hour on a
1200 psig D type boiler? - CORRECT ANSWER-1020 degrees



What is the first action taken, when you are experiencing difficulty in maintaining boiler water level on
an automated ship? - CORRECT ANSWER-Shift boiler feed water control to remote/manual



In the engineering bell book, what does I mean? - CORRECT ANSWER-Ahead standard speed



In the engineering bell book, what does III mean? - CORRECT ANSWER-Ahead flank speed



In the engineering bell book, what does B 1/3 mean? - CORRECT ANSWER-Back 1/3 speed



In the engineering bell book, what does Z mean? - CORRECT ANSWER-Stop



In the engineering bell book, what does BF mean? - CORRECT ANSWER-Back full speed



In the engineering bell book, what does BEM mean? - CORRECT ANSWER-Back emergency speed



In the engineering bell book, what does II mean? - CORRECT ANSWER-Ahead full speed



When order received is recorded as RPM in what column? - CORRECT ANSWER-2



What QA for is used for testing and inspection? - CORRECT ANSWER-QA form 17



Boiler high water alarm is set to what parameter - CORRECT ANSWER-+7 inches

, During a white smoke casualty to a boiler, what must never be adjusted? - CORRECT ANSWER-Fuel oil
header pressure



What temp is lube oil maintained on an operating main engine? - CORRECT ANSWER-120-130 degrees



A ruptured feed water control valve diaphragm will have what adverse effect on boiler water level? -
CORRECT ANSWER-Water level increase

Valve will fail open



Maximum steady state superheater outlet temp on a D type 1200 psig boiler? - CORRECT ANSWER-1000
degrees



During loss of vacuum casualty on a main condenser, what action must be taken when vacuum
decreases to 15"? - CORRECT ANSWER-Main engine must be stopped and casualty procedure IAW EOCC



Temporary distortion of SSTG rotor numerous start/stop episodes is known as what? - CORRECT
ANSWER-Bowed rotor



Whenever a propulsion turbine casing joint is opened for any reason, a final contact check is required by
taking a red and blue check of the made up joint, what is the required contact for non pumping groove
joints? - CORRECT ANSWER-75% contact over entire joint, 1/4" minimum continuous contact inside the
groove and across each pressure section



What is the function of staff packing on SSTG - CORRECT ANSWER-Prevent leakage of stem from ingress
of air into turbines



Prior to conducting thrust measurements on a main engine, turbine must be at ambient temp with
throttles shit for how long? - CORRECT ANSWER-24 hours



Main engine turbine bearings are measured for wear at what normal interval? - CORRECT ANSWER-
Annually

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller 2024newestexams. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for $22.49. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

80364 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy study notes for 14 years now

Start selling
$22.49
  • (0)
  Add to cart