100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
EWRB Exam – Questions With Complete Solutions (A+) $9.99   Add to cart

Exam (elaborations)

EWRB Exam – Questions With Complete Solutions (A+)

 6 views  0 purchase
  • Course
  • EWRB
  • Institution
  • EWRB

EWRB Exam – Questions With Complete Solutions (A+)

Preview 2 out of 5  pages

  • October 9, 2024
  • 5
  • 2024/2025
  • Exam (elaborations)
  • Questions & answers
  • EWRB
  • EWRB
avatar-seller
Zendaya
EWRB Exam – Questions With Complete Solutions (A+)

State the main reason why a large industrial electrical installation has a higher
prospective short circuit current (PSSC) than a domestic electrical installation.
Right Ans - The fault loop impedance is lower
Because the distribution transformer is close to the installation or on-site

A CT metering circuit is measuring the consumption of an industrial electrical
installation at near to full load. The CT secondary must be shortcircuited
before disconnecting the meters from the CT. State TWO reasons why the CT
secondary must be short-circuited Right Ans - To prevent a high voltage
developing in the circuit.
To prevent damage to the CT winding insulation.

A result of fault loop impedance test at the main switchboard of a low voltage
electrical installation will show the prospective short circuit current level of
the installation or the impedance of the fault loop at the switchboard under
fault conditions. State the main purpose of the information gained from the
earth fault loop impedance test Right Ans - To confirm that the protective
devices can safely interrupt the installation PSSC.

Some protective devices in an electrical installation have a fault duty lower
than the prospective short circuit rating of the installation. State the main
hazard that could occur when a high prospective short-circuit fault current
occurs in the electrical installation. Right Ans - Flash over on switchboards
due to inadequate kA rating of protective devices

AS/NZS 3000 requires that a test voltage of 500V d.c. is used for an insulation
resistance test of a low voltage electrical installation.
Explain why a voltage of 500V is applied. Right Ans - To stress the
insulation at a voltage above 325V a.c. (or peak a.c. voltage.

AS/NZS 3000 requires that a test voltage of 500V d.c. is used for an insulation
resistance test of a low voltage electrical installation.
Explain why the voltage is a d.c. voltage. Right Ans - To ensure capacitive or
inductive reactance does not influence the test result.
A constant maximum voltage is a more stringent test than the momentary
peaks of an a.c. waveform.

, AS/NZS 3000 requires that a test voltage of 500V d.c. is used for an insulation
resistance test of a low voltage electrical installation.
Define the term current rating as it applies to an HRC fuse? Right Ans - This
is the maximum current that the fuse is designed to carry continuously

AS/NZS 3000 requires that a test voltage of 500V d.c. is used for an insulation
resistance test of a low voltage electrical installation.
Define the term breaking (or rupturing) capacity as it applies to an HRC fuse
Right Ans - The maximum fault current the fuse can safely interrupt.

State TWO technical advantages that a soft starter has when compared to and
electromechanical type starter, such as auto-transformer. Right Ans -
Broad range of options for starting and stopping
Broad range of options for protection.
Visual feedback of key technical parameters.
Smoother starting
Reduced mechanical stress on equipment on starting. Reduced electrical
stress on equipment on starting

Explain the purpose of an interlocks in a star/delta starter Right Ans - To
prevent the star and delta contactors closing simultaneously

State the effect of the interlocks failing in a star/delta starter Right Ans - An
electrical interlock failure could prevent the motor starting. An electrical
interlock failure could cause a phase-to-phase short.
A mechanical interlock failure could prevent the motor starting.
A mechanical interlock failure could cause a phase-to-phase short.

Define the term pullout torque as it applies to an a.c. induction motor Right
Ans - The maximum torque the motor can develop.

State the synchronous speed of a three-phase, four-pole, 50 Hz motor.
Right Ans - 1500 rpm

State the Standard and section of that Standard that specifies the tests and
checks that need to be carried out on the socket outlet and final subcircuit
wiring. Right Ans - AS/NZS 3000
Section 8

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller Zendaya. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for $9.99. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

79373 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy study notes for 14 years now

Start selling
$9.99
  • (0)
  Add to cart