Michigan State Brakes Certification Exam Questions With Verified Answers.
6 views 0 purchase
Course
Michigan State Brakes
Institution
Michigan State Brakes
Michigan State Brakes Certification Exam
Questions With Verified Answers.
Most 1995 & newer vehicles use which of the following types of wheels bearings on non-drive
wheel? - answerSealed non-serviceable
to test a vacuum power brake booster in the vehicle, you should pump the brake pedal at lea...
Michigan State Brakes Certification Exam
Questions With Verified Answers.
Most 1995 & newer vehicles use which of the following types of wheels bearings on non-drive
wheel? - answer✔Sealed non-serviceable
to test a vacuum power brake booster in the vehicle, you should pump the brake pedal at least 4
times, hold the brake pedal depressed, and start the engine. the brake pedal should: -
answer✔drop slightly and remain firm
You are installing a set of brake shoe linings that are not the same length. Traditionally, the
primary shoe lining is: - answer✔Smaller and goes towards the front of the car.
A cracked or torn vacuum diaphragm in a brake power booster would most likely cause: -
answer✔a hard pedal feel requiring very high pedal effort to stop
A mechanic finds gear lube inside both rear brake drums on a rear wheel drive vehicle. What is
the most likely cause of this problem? - answer✔A plugged axle
Which of the following incorrect service procedures will cause brake lock-up? - answer✔master
cylinder push rod adjusted too long
Which of the following describes the proper way to depressurized an ABS system? -
answer✔Pump the brake pedal at least 25 times (or more, depending on the manufacturer's
recommendation) with the ignition off.
The rear brakes are dragging after having new linings installed and the drums machined. the
most likely cause is the: - answer✔technician use the parking brake to adjust shoes and the cable
is stuck
When turning brake drums: - answer✔use a dampening strap to reduce chatter
Which of the following is NOT a necessary drum brake measurement? - answer✔run-out
On a 3-channel system, which wheels are on the same circuit? - answer✔both rear wheels
One way to test an ABS wheel speed signal is to use _____ on your digital multimeter. -
answer✔AC volts
The key input for the ABS control module comes from the: - answer✔wheel speed sensors
ABS speed sensor and sensor rings: - answer✔should not be hammered or tapped on and should
always be replaced as a matched set
Flexible brake hoses should be replaced: - answer✔when dampness is evident on the hose
Which of the following should be used to check for rotor thickness variation: -
answer✔Micrometer
After rebuilding a master cylinder, the rod between the master cylinder and booster should be: -
answer✔adjusted properly
Upon inspecting brake fluid condition, the technician observes the diaphragm in the master
cylinder cup is swollen. Which of the following is the most likely cause? - answer✔silicone fluid
added to the system
When inspecting brake fluid levels, a technician observes low fluid levels. which of the
following should be done first? - answer✔Inspect disc brake pads for excessive wear
Which of the following is true about most properly functioning anti-lock brake systems? -
answer✔The brakes may lock up at speeds less than 10 miles per hour
Which of the following is true about bleeding brake lines on most ABS equipped vehicles? -
answer✔Most ABS brake lines can be bled like a conventional (non-ABS) system. However,
caution must be taken because of the extreme pressure.
Most anti-lock brake systems require the removal of the pressure modulator fuse when: -
answer✔a "spaced-saver" spare tire is being used and mismatched tires are being installed
What does a load sensing proportioning valve do? - answer✔It increases the hydraulic pressure
during braking at the rear wheel cylinders when the vehicle is loaded
The brakes of a car squeal each time they are applied, which of the following is the LEAST
likely source of the noise? - answer✔Glazed brake pads
Which of the following is a true statement about proportioning valves? - answer✔They provide
better braking balance during hard stops
A properly functioning load sensing proportioning valve will: - answer✔cause an increase in the
hydraulic pressure during braking at the rear wheel cylinders when the vehicle is loaded.
Why don't disc brake system usually need adjustment? - answer✔A certain amount of pressure is
maintained by the metering valve
The front brakes of a car equipped with disc brakes in the front and drum brakes in the rear, grab
quickly as light pressure is applied to the brake pedal, which of the following could be the cause
of the problem? - answer✔Defective metering valve
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Brainbarter. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $10.49. You're not tied to anything after your purchase.