100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
CWB level 1 exam prep Latest Update Actual Exam 115 Questions and 100% Verified Correct Answers Guaranteed A+ $20.49   Add to cart

Exam (elaborations)

CWB level 1 exam prep Latest Update Actual Exam 115 Questions and 100% Verified Correct Answers Guaranteed A+

 3 views  0 purchase
  • Course
  • CWB level 1
  • Institution
  • CWB Level 1

CWB level 1 exam prep Latest Update Actual Exam 115 Questions and 100% Verified Correct Answers Guaranteed A+

Preview 4 out of 35  pages

  • September 26, 2024
  • 35
  • 2024/2025
  • Exam (elaborations)
  • Questions & answers
  • CWB level 1
  • CWB level 1
avatar-seller
Tutordiligent
CWB level 1 exam prep Latest Update 2024-2025
Actual Exam 115 Questions and 100% Verified
Correct Answers Guaranteed A+

1. Which is not a recommended method for surface cleaning of a part for liquid
penetrant examination?
a) Cleaning with organic solvents.
b) Blasting with shot or dull sand.
c) Cleaning with de-greasers.
d) Use of de-scaling solutions.
e) Ultrasonic cleaning methods. - CORRECT ANSWER: b) Blasting with shot or dull
sand.


2. Which of the following weld defects is most likely to be missed by radiography in a
weld:
a) Undercutting.
b) Porosity.
c) Slag inclusions.
d) Cracking.
e) Burn through . - CORRECT ANSWER: d) Cracking.


3. In the choices given below, metallographic tests would be the least informative with
regard to the:
a) Presence of the non-metallic inclusions.
b) Grain structure in the weld and fusion zone.
c) Ability of the material to withstand repeated fluctuating loads.
d) Extent and structure of the heat affected zone.
e) Number of weld passes. - CORRECT ANSWER: c) Ability of the material to withstand
repeated fluctuating loads.

,4. In producing a drawing for a scale of 1:50, what would be the distance represented
by a distance on
the drawing of 6 em?
a) 12 cm.
b) 30 cm.
c) 50 cm.
d) 240 cm.
e) 300 cm. - CORRECT ANSWER: e) 300 cm.


5. The mechanical test used to determine the ability of a material to resist failure by
brittle fracture
requires the use of:
a) A tensile test specimen.
b) A bend test specimen.
c) A compression test specimen.
d) An impact test specimen.
e) A spectrographic test. - CORRECT ANSWER: d) An impact test specimen.


6. The cooling rate of aT-joint is:
a) Less than that in a butt joint.
b) Greater than that in a butt joint.
c) Greater than that in a butt joint only where the carbon equivalent is high .
d) Greater at the mid-section than at the start.
e) Greater at the mid-section than at the finish. - CORRECT ANSWER: b) Greater than
that in a butt joint.


7. What are slag and non-metallic inclusions usually caused by?
a) Moisture in the weld joint.

,b) High welding current.
c) Loss of shielding gas.
d) Inadequate interpass cleaning. - CORRECT ANSWER: d) Inadequate interpass
cleaning.


8. Where deviations from the drawings are warranted the inspector should do which of
the following?
a) Authorize approval of the changes.
b) Obtain official approval for the changes.
c) Reject the work without any further consideration.
d) Stop the work until drawing revisions have been completed. - CORRECT ANSWER:
b) Obtain official approval for the changes.


9. With the appropriate electrode, which of the following welding processes can operate
with or without
a shielding gas:
a) Electrogas welding process.
b) Gas metal arc welding process.
c) Flux cored arc welding process.
d) Submerged arc welding process.
e) Pulsed gas metal arc welding process. - CORRECT ANSWER: c) Flux cored arc
welding process.


10. If there is inadequate penetration at the root of a double vee groove, which of the
following
statements best defines the reason for this:
a) Groove angle exceeds specified amount.
b) Root opening too large.
c) Groove depth too large causing melt through on the second side
d) Groove angle is too small.

, e) Excessive plate thickness. - CORRECT ANSWER: d) Groove angle is too small


11. The continuous method of magnetic particle inspection means:
a) Carrying out all the steps in the process without pause.
b) Using DC current.
c) Applying magnetic particles to the weld while the current is flowing in the yoke.
d) Applying magnetic particle to the test surface while current flows from one leg of the
yoke
through the material to the other leg of the yoke.
e) Precautions must be taken to prevent over-magnetization of the material. -
CORRECT ANSWER: c) Applying magnetic particles to the weld while the current is
flowing in the yoke.


12. From the welding problems identified below which one of the five does not fit the
pattern established
by the other four?
a) Insufficient throat.
b) Incorrect bevel angle.
c) Loss of shielding gas.
d) Improper fit up.
e) Use of wrong consumable. - CORRECT ANSWER: a) Insufficient throat.


13. A 10 mm fillet weld has a nominal:
a) Throat dimension of 10 mm.
b) Area of 10 sq. mm.
c) Leg size of 1 0 mm.
d) Face width of 10 mm. - CORRECT ANSWER: c) Leg size of 1 0 mm.


14. Which welding process has an arc drawn between the workpiece and the member
being welded to

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller Tutordiligent. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for $20.49. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

85073 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy study notes for 14 years now

Start selling
$20.49
  • (0)
  Add to cart