API 570 OPEN BOOK EXAM | COMPLETE SOLUTION| 100% CORRECT.
13 views 0 purchase
Course
Open Book.
Institution
Open Book.
API 570 OPEN BOOK EXAM | COMPLETE SOLUTION| 100% CORRECT.
1- A hydrotest is being conducted on an underground line as a substitute for the external inspection. The test pressure is 200 psig. At the end of the test, the pressure must be at least: - C.190 psig
2- Determine the maximum al...
API 570 OPEN BOOK EXAM | COMPLETE
SOLUTION| 100% CORRECT.
1- A hydrotest is being conducted on an underground line as a substitute for the
external inspection. The test pressure is 200 psig. At the end of the test, the pressure
must be at least: - C.190 psig
2- Determine the maximum allowed pressure for a class 300 flange that has a design
temperature of 950 degrees F. The flange material is ASTM A217 gr.C12 - B. 375 psig
3- An 8 NPS pipe is being replaced with A106 gr. B material. The pipe retirement
thickness is 0.218" and the corrosion allowance is 0.125". What is the minimum
thickness of pipe that could be ordered after adjusting for mill-tolerance. - E. 0.392"
4- A welder is being qualified by RT on a 0.600" plate using the SMAW process. What is
the maximum allowed length of an individual elongated slag inclusion for this qualifying
test? - B. 0.200"
5- During the evaluation of a radiograph, the density at the IQI is 3.0. What is the
minimum density allowed on this radiograph in the weld? - C. 2.55
6- A liquid Penentrant procedure must be qualified when performinf the examination: -
C. on materials below 40 degrees F.
7- If the "A-Number" on the PQR is an A-2, what "A-Number" must be on the WPS? -
C. A-1 or A-2
8- When welding pipe, peeing is prohibited on: - D. only the root and final passes.
9- What is the diameter of the bolts that are used for a 6 NPS class 600 flange? - A.
1.00 inch
10- The size of a fillet weld refers to the fillet weld's: - A. Leg
What is the "F- Number" for an E-7018 electrode? - D. F-4
12- For class 2 piping system, a location should consider performing CUI inspection on:
- B. 33% of suspect areas
13- the set pressure for a relief device protecting piping systems shall be: - D. set in
accordance with ASME B&PV section VIII
, 14- When performing a WFMPT examination, prior to the examination, the examiner
shall be in a darkened area for: - C. 5 minutes
15- What is the maximum allowed hydrotest pressure for piping system with class 300
flanges that are made of ASTM A182 gr. F316 material? the sustem has a design
temperature of 600 degrees F. - F. 1100 psig
16- What is the required preheat for an A 106 gr. B pipe that has a wall thickness of
0.500"? - E. preheat is not required
17- According to B31.3 a 1-1/2 NPS carbon steel threaded pipe that is installed in a
Normal Service should have a minimum wall thickness of: - C. schedule 80.
18- Which of the following is an essential variable for welder qualification using the
SMAW process? - B. deletion of backing
19- Without performing impact tests, what is the minimum allowed temperature for the
following piping system?
Material: A106 gr. B
Line size: 6 NPS
Nominal thickness: 0.750"
Retirement thickness: 0.500" - C. +15 degrees F.
20- A tensile test specimen breaks at 18,750 lbs. The specimen is 3/4"wide and 1/2"
thick. What is the tensile strength of the specimen? - D. 50,000 psi
21- During the design of a pipe alteration, it is determined that impact testing of the pipe
is required. The pipe material is a A106 gr. C and is considered a fully deoxidized steel.
During impact testinf each specimen should break at or above: - 12 ft-lbs
22- Joe Welder qualifiedusing a 4G coupon that is 0.625" thick. The qualification weld
was made with 4 layers. What is the maximum weld material thickness that Joe is now
qualified to weld? - D. Unlimited
23- What is the retirement thickness of the described pipe?
Design Pressure: 500 psig Size: 12 NPS
Design temperature: 700 degrees F
Material: A106 gr. B
Original corrosion allowence: 0.125" - D. 0.191"
24- During radiography of a weld that is 1.0" thick, what is the maximum allowed
geometric unsharpness in the radiograph? - C. 0.020
25- An existing line is replaces with 9 Cr- 1 Mo(A426 gr. CP9). The design conditions
are 700 degrees F at 250 psig. The authorize inspector determines that a hydrotest
should be performed. What is the minimum required hydrotest pressure? - D. 511 psig
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Mboffin. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $11.49. You're not tied to anything after your purchase.
