1. 1.To measure the strength of a welded joint what mechanical test would youprescribe?
a) A transverse weld tension test
b) A charpy test.
c) A CTOD test.
d) An all weld metal tension test.
e) A side bend test.
Answer: a) A transverse weldtension test
2. 2. Select the cutting process that would provide the narrowest heat affectedzone when
cutting 12.5 mm (0.5 in) thick carbon steel.
a) Oxy-acetylene cutting.
b) Air-carbon arc cutting.
c) Oxy-propane cutting.
d) Plasma arc cutting.
e) Laser beam cutting
Answer: e) Laser beam cutting
3. 3. Which of the following refers to a welder test where a pipe assemblyis placed vertically
and the joint welded in the horizontal position withoutrotating the assembly?
a) 1G
b) 2G
c) 3G
d) 5G
e) 6G
Answer: b) 2G
4. 4. Which of the following imperfections is normally considered as unacceptable regardless of
size or location?
a) Porosity.
b) Crack.
c) Inadequate penetration.
d) Lamination.
e) Burn-through.
Answer: b) Crack.
5. 5. Select the correct penetrameter thickness for 2% sensitivity when radiographing a
weldment 1 .25 inches in thickness.
a) 0.012 in.
b) 0.015 in.
c) 0.025 in
, d) 0.030 in.
Answer: c) 0.025 in
6. 6. Which of the following statements concerning porosity is true?
a) Porosity cannot be trapped within a weld.
b) Porosity moves up through later passes and will show only in a final pass.
c) Porosity is restricted to the centre line of a weld.
d) Porosity can result from faulty welder technique.
e) Porosity can be dissipated by an appropriate heat treatment.
Answer: d) Porosity canresult from faulty welder technique.
7. 7. An irregular, dense white spot is seen on the radiograph of a weld. Assuming it was
caused by the welding process used, which one of theprocesses below would be responsible?
a) SMAW process.
b) GTAW process.
c) GMAW process.
d) ST process.
e) ESW process.
Answer: b) GTAW process.
8. 8. Which of the following operations is known to result in the emission ofionizing radiation
at levels dangerous to human health?
A) shield metal arc welding.
B) Plasma arc welding.
C) Operation of high voltage portable generator sets.
d) Radiographic inspection.
e) Electroslag and electrogas welding.
Answer: d) Radiographic inspection.
9. 9. The ultrasonic transducer is pressed against the plate of a welded joint.
The sound travels longitudinally through the plate to the opposite side. The signal seen on the
UT screen that comes from this opposite side of the plate:
a) Is the initial pulse signal.
b) Is the back reflection signal.
c) Is the front reflection signal.
d) Must be equal in amplitude to any defect signal.
e) Cannot be used for establishing the thickness of the material under test.
Answer: b)Is the back reflection signal.
10. 11. Which of the following is a stainless steel electrode?
a) E4918-1
b) E4918-A1
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller ExamNavigator. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $10.99. You're not tied to anything after your purchase.
