ICC Masonry Exam Study Questions With Collect Answers
3 views 0 purchase
Course
ICC Masonry
Institution
ICC Masonry
ICC Masonry Exam Study Questions With Collect Answers
A method of proportioning structural members such that the computed forces produced in the members by factored loads do not exceed the member design strength, also called load and resistance Factor design. The term strength design is used in ...
A method of proportioning structural members such that the computed forces produced
in the members by factored loads do not exceed the member design strength, also
called load and resistance Factor design. The term strength design is used in design of
Concrete & Masonry structural elements. - Answer-Strength design; IBC Definitions
/.A method of proportioning structural members, such that elastically computed stresses
produced in the members by nominal loads do not exceed specified allowable stresses.
Also called working stress design - Answer-Allowable stress design; IBC Definitions
/.A void space having a gross cross-sectional area greater than one and a half square
inches - Answer-Cell (masonry); IBC Definitions
/.After construction and grouting, masonry test prisms should not be
disturbed or moved for a minimum of - Answer-48 hours; ASTM - C 1314, Section 5.10
/.After excess water is absorbed into the masonry, what must be done to
remove the film of water between the masonry shell and the grout? - Answer-The grout
must be reconsolidated; RCMC 6th Edition, Section 6.8
/.After initial mixing, when the ambient temperature exceeds 90
degrees F with a wind velocity over 8 mph, mortar used in masonry
construction must be discarded after - Answer-2 hours; 2006 IBC 2104.4.2.1
/.After introducing water to the grout mixture, grout must be placed
within - Answer-1 1/2 hours; RCMCI 6th Edition, Section 6.4
/.C.C.R. Title 24 requires reinforcing steel spacing is to be at a
maximum of 2 feet each way and a minimum splice of - Answer-48 bar diameters;
RGBM 14th Edition, page 88 5.9
/.Cleanout openings are not required for - Answer-Low-lift grouting; RCMCI 6th Edition,
Section 6.5
/.Cleanouts are required for pours over - Answer-5 ft; ACI 530, SC-20, section 3.5D
/.Eight classification assigned to a structure based on its risk category and the severity
of the design earthquake ground motion at the site. - Answer-Seismic design category;
IBC Definitions
, /.For grout lifts over 5 feet, what is the time period stipulated to provide sufficient curing
time to minimize potential displacement of units during the consolidation and
reconsolidation process? - Answer-4 hours; ACI 530, SC-20, section 3.5D
/.For grouting between masonry withes, what is the minimum width of the grout space
required for a grout pour height of 5 feet? - Answer-2"; ACI 530, C-21, Table 1.16.1
/.For how many square feet of wall must you saw cut a minimum of how many prisons
for a completed Masonry? - Answer-5000, three; 602 S21 1.4 B.4.a
/.For reinforced grouted-brick masonry, the minimum reinforcing bar lap length required
for Grade 40 steel is - Answer-40 bar diameters; RGBM 14th Edition, Section 5.13
/.Glass unit masonry shall not be laid at temperatures below - Answer-60 degrees F;
2006 IBC 2104.3.2.1
/.Grout intended for use in the construction of engineered and
empirically designed masonry structures must comply with - Answer-ASTM C 476; 2006
IBC 2103.12
/.Grout must be consolidated by mechanical means when the grout lift exceeds -
Answer-12"; RCMC 6th Edition - section 6.8
/.If mortar compression tests are required, how many tests per day are to be taken for
the three successive work days at the start of the job? - Answer-1; RCMCI 6th Edition,
3.2.4
/.In high-lift grouting, what is the maximum height masonry walls
may be built to? - Answer-24'; RCMCI 6th Edition, Section 6.7
/.In hollow-unit grouted brick masonry, a fine grout pour of 8 feet
requires a minimum total clear area dimension within the grout spaces
and cells of - Answer-1 1/2" X 3"; RGBM 14th Edition, Section 3.2
/.In masonry construction, what is the maximum tolerance permitted
for vertical alignment of nonbearing columns and walls? - Answer-+/- 3/4"; ACI 530, S-
21, Section 3.3G (2) (d)
/.In masonry construction, what type of joint is used to allow
dimensional changes in masonry, minimize random wall cracks and
other distress? - Answer-Movement joint; ACI 530
/.In masonry not exposed to earth or weather, reinforcing bars shall
have a minimum masonry cover of not less than - Answer-1 1/2"; ACI 530
/.In solid-grouted masonry, cleanouts must be spaced horizontally at a
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller kartelo. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $8.49. You're not tied to anything after your purchase.
