Exam (elaborations)
ASME B31.3 PROCESS PIPING CODE EXAM
- Course
- Institution
ASME B31.3 PROCESS PIPING CODE EXAM ....
[Show more]
Content preview
ASME B31.3 PROCESS PIPING CODE EXAM2024-2025
The requirements of the most recent edition of ASME Code B31.3, and any future
addenda: - ANSWER Are not retroactive, and all equipment installed in older
editions does not need to be upgraded.
Clauses in the B31 code are not always numbered consecutively. Such
discontinuities result from ANSWER Insofar as is practical, all code parts should
follow a common outline.
Who is responsible for establishing which code section applies to plumbing
installations, such as B31.1, B31.3, and so on? - ANSWER Owner.
Who is ultimately responsible for ensuring ASME B31.3 compliance? - ANSWER
Owner.
ASME B31.3 is intended to establish forth engineering specifications deemed
required for ________. Pipeline installations should be designed and built safely.
The ASME code is not designed to apply to plumbing. - ANSWER That has been
put into service.
Material compatibility with the service, as well as dangers resulting from fluid
instability: - ANSWER Are outside the scope of ASME B31.3.
ASME B31.3 covers pipework for all fluids except: - ANSWER Tubes for fired
heaters, plumbing, and storm drains.
,A prep-laced filler metal that is fully melted into the root of a welded connection
and becomes part of the weld is called: - ANSWER A consumable insert.
Define "face of weld". - ANSWER It is the exposed surface of a weld on the side
from whence it was created.
A category _____ fluid is neither flammable, harmless, or harmful to human tissue,
has a gage pressure of no more than 150 psi, and has a design temperature range of
-20 degrees to 366 degrees Fahrenheit. - Answer D.
A category ______ fluid has the potential for significant personnel exposure and
where a single exposure to a very small quantity of toxic fluid, caused by leakage,
can cause serious irreversible harm to people on breathing or bodily contact, even
when prompt restorative measures are taken. - ANSWER M
A fillet weld that is equal to the thickness of the thinner element connected is
called: - ANSWER A full fillet weld.
The heating and holding of metal to a suitable temperature and then cooling at a
suitable rate for such purposes as: reducing hardness, improving machinability,
facilitating cold working, producing a desired microstructure, or obtaining desired
mechanical, physical, or other properties is known as: - ANSWER Annealing.
A piping joint that provides mechanical strength through threaded, grooved, rolled,
flared, or flanged pipe ends, or bolts, pins, toggles, or rings, and leak resistance
through threads and compounds, gaskets, rolled ends, caulking, or machined and
mated surfaces is known as: - ANSWER: Mechanical joint
The word NPS 6 refers to: - A pipe with an outer diameter of 6.625 inches.
A pipe made by piercing a billet and then rolling, drawing, or both is called a: -
ANSWER Seamless pipe
, What is a root opening? - ANSWER It is the gap between the parts that will be
united by welding at the joint's root.
A weld designed primarily to ensure junction tightness against leaking in metallic
pipework is known as: - Answer: Seal weld
A tack weld is created to keep the components of a weld in perfect alignment until
the final welds are made.
The intersection between the face of the weld and the base metal is known as the
"toe of the weld."
The pressure in a piping system that is the pressure at the most severe condition of
coincident internal or external pressure and temperature (minimum or maximum)
expected during service (except for allowances for occasional variations in
pressure, temperature, or both, above operating levels, which are characteristics of
certain services) is known as: - ANSWER: Design pressure
Piping that is not protected by a pressure relieving device or that can be detached
from a pressure relieving device must be constructed for at least the following: -
Maximum pressure that can be created.
What happens if a piping system containing gas or vapor is allowed to cool
significantly? - ANSWER The pressure in the pipe system may drop enough to
create an internal vacuum.
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Mirror. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $11.49. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
73773 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now