Exam (elaborations)
ASM CDC VOLUME 1 EXAM QUESTIONS WITH VERIFIED ANSWERS
- Course
- Institution
ASM CDC VOLUME 1 EXAM QUESTIONS WITH VERIFIED ANSWERS...
[Show more]
Content preview
ASM CDC VOLUME 1 EXAM QUESTIONS WITHVERIFIED ANSWERS
A riveting hammer is used to drive rivets and execute mild chiselling.
Setting down, clinching, or tucking in the edges of sheet metal - ANSWER: What
are you most likely doing using a setting hammer?
Stretching - ANSWER: What type of hammer should you use to create concave
forms in soft metal?
8oz ball peen - ANSWER: What type and size hammer do you use to centre punch
holes before drilling?
mallet - ANSWER What type of pounding tool is used for finishing?
When is a centre punch utilized before a drilling or punching operation?
Prick - ANSWER: What type of punch is used to mark location points when laying
up patterns on sheet stock?
Taper punch - ANSWER: What is another term for drift punch?
pin - What punch is used to remove rivet shanks from drilled holes?
If it does not have a taper, how does a pin punch differ from other types of
punches?
ANSWER: A steel rule can perform two functions: measuring and straight edge.
,When creating sliced lines on metal. - ANSWER When should you use a scriber?
Dividers can be used to measure distances between two spots for transferring or
comparing measurements directly from a rule.
Draw lines with angles ranging from 0 to 180 degrees. - ANSWER: What do you
use the combination set's protractor head for?
The centre punch has a larger tip, which allows for deeper depressions. -
ANSWER: Why is a centre punch used instead of a prick punch to mark the centres
of holes to be drilled?
The depth of a corrosion pit. - ANSWER: What do you measure using a depth
gauge?
Zero the gauge. - ANSWER What should you do before measuring anything with
the depth gauge?
The depth of a pit is calculated using the formula ((A+B)/2) - C.
grams - ANSWER When using a scale, which unit of measurement is preferred?
Any residue left behind impairs future usage of the scale. - ANSWER: Why should
you keep the scale clear of foreign residue?
Straight. - ANSWER If you need to cut a triangle from a tiny piece of metal, which
type of snips work best?
,To allow you to view the cut line. - ANSWER: Why should you cut a circle with
straight snips counterclockwise?
straight - ANSWER: What sort of snip can be sharpened when it becomes dull?
QUESTION - ANSWER If you need to enlarge a small hole in a piece of metal,
what type of snips do you use?
QUESTION - ANSWER If you're utilizing the upper blade as a guide during a
cutting operation, what kind of snips are you likely employing?
single - ANSWER: What kind of file cut do you use to sharpen shear or snip
blades?
flat - ANSWER Which file type is best suitable for routine filing operations?
triangle - Which sort of file is used to file cutters and taps?
Because the cutting teeth slant forward, the pressure from the back stroke will most
likely break them off. - ANSWER: Why is pressure on the back stroke typically not
allowed when filing?
When filing extremely soft materials. - ANSWER: When should you apply a light
pressure to the back stroke during filing?
, To prevent vibration, place it near the vise jaws and, if the surface is straight,
parallel to the vise's top. - ANSWER: How should material for crossfiling be held
in a vise?
When a finer finish is required. - ANSWER: When do you file a piece of metal?
Always use the file handle. - ANSWER: What is the most important precaution to
take before using a file?
Chipping and cutting sheet metal, screw heads, and flat stock. - ANSWER What is
the proper use of a flat chisel?
The half roundnose cuts concave grooves, while the cape cuts grooves, slots, and
keyways, as well as flat surfaces that are too thin for a flat chisel. - ANSWER:
What are half roundnose and cape chisels used for?
To carve V-shaped grooves, what is the proper use of a diamond point chisel?
Pressing too firmly on the wheel, causing excessive heat to be generated. -
ANSWER: What causes a chisel to soften and lose toughness when sharpened?
All-hard blade with 18 teeth per inch. - ANSWER: What type and pitch of blade do
you use to cut solid aluminum?
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Mirror. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $11.49. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
81989 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now