Exam (elaborations)
ASE TEST T2 PRACTICE TEST 2 QUESTIONS AND ANSWERS WITH SOLUTIONS 2024
- Course
- Institution
ASE TEST T2 PRACTICE TEST 2 QUESTIONS AND ANSWERS WITH SOLUTIONS 2024
[Show more]
Content preview
ASE TEST T2 PRACTICE TEST 2QUESTIONS AND ANSWERS WITH
SOLUTIONS 2024
A diesel engine is using too much oil. All of the following could be the cause EXCEPT
A. Worn piston rings
B. Worn valve guides
C. Worn valve seats
D. Loose oil pan fasteners - ANSWER C. Worn valve seats (work valve seats can cause low compression,
but will not cause oil consumption)
Which of the following would be used to check liner installed height?
A. Dial indicator/ Sled gage
B. Inside micrometer
C. Outside micrometer
D. Dial caliper - ANSWER A. Dial indicator/ Sled gage ( A Dial indicator, sometimes known as a sled gage,
is normally used to check liner installed height)
The fuel drains back to the tank after sitting overnight, which of the following could be the cause?
A. A stuck open return check valve
B. A stuck closed return check valve
C. A restricted supply line
D. A restricted return live - ANSWER A. A stuck open return check valve ( A stuck open return check valve
can allow fuel to drain back to the tank if the return line is not in submerged fuel)
In reference to the illustration technician A says that when replacing a turbocharger assembly, the drain
line should be checked for restriction. Technician B says that turbochargers are often recored by
,replacing the center housing as a unit and reusing the old compressor and turbine housing, who is
correct?
A. A only
B. B only
C. Both A and B
D. Neither A or B - ANSWER C. Both A and B (both technicians are correct. When replacing a turbo
charger, it is a good practice to inspect the oil supply and return lines to ensure proper lubricant flow at
the replacement turbo charger. This can reduce the chances of the replacement turbo failing. Technician
B is also correct. Turbo chargers can recored; this helps to reduce repair costs, requiring can only be
performed if both the turbine and impeller housing's are in good condition).
A diesel engine shows an abnormally high reading on the temperature gauge, and the top radiator hose
is cold. which of the following is the most likely cause?
A. Stuck open thermostat
B. Stuck closed thermostat
C. Restricted radiator
D. Restricted charge air cooler - ANSWER B. Stuck closed thermostat ( A stuck closed thermostat would
allow the engine to overheat and the top radiator hose to be cold because the coolant is not circulating)
The regulating valve on a fuel injection pump is stuck open. This will result in:
A. Low fuel-supply pressure
B. High fuel-supply pressure
C. Engine overheating
D. Low oil pressure - ANSWER A. Low fuel-supply pressure ( The regulating valve helps to hold pressure in
the low pressure fuel system; if it were stuck open, the fuel pressure would be low)
A diesel engine that has high oil consumption also has oil in the charge air cooler. Technician A says the
air compressor oil drain line may be restricted. Technician B says the turbocharger oil drain line may be
restricted. Who is correct?
, A. A only
B. B only
C. Both A and B
D. Neither A nor B - ANSWER B. B only (Only Technician B is correct. A restricted turbo oil drain in line
can cause the turbo seals to leak and allow oil to travel into the charge air cooler.)
A diesel engine equipped with a common-rail fuel system blows excessive smoke. Technician A says the
boost pressure sensor may be faulty. Technician B says the coolant temperature sensor may be faulty.
Who is correct?
A. A only
B. B only
C. Both A and B
D. Neither A nor B - ANSWER A. A only (Only Technician A is correct. A failed boost pressure sensor could
cause the electronic control module (ECM) to over-fuel the engine, resulting in black smoke)
All of the following must be checked after a diesel cylinder head has been milled EXCEPT:
A. Injector tip protrusion
B. Intake valve head protrusion
C. Valve stem height
D. Exhaust valve head protrusion - ANSWER C. Valve stem height (Milling the cylinder head deck surface
will not affect the distance the protrude farther into the combustion chamber.)
An engine is being assembled, and the crankshaft end-play is greater than the specification. Which of the
following could be the cause?
A. Crankshaft rod journal is out of round
B. Crankshaft rod journal is tapered
C. Worn crankshaft thrust surface
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Performance. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $15.99. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
72042 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now