Exam (elaborations)
Mechanic Exam Questions and Answers (Verified Answers by Expert).
Mechanic Exam Questions and Answers (Verified Answers by Expert).
[Show more]
Uploaded on
August 13, 2024
Number of pages
9
Written in
2024/2025
Type
Exam (elaborations)
Contains
Questions & answers
$11.49
Also available in package deal from $30.99
100% satisfaction guarantee
Immediately available after payment
Both online and in PDF
No strings attached
Also available in package deal (1)
1. Exam (elaborations) - Mechanic exam questions and answers (verified answers by expert).
2. Exam (elaborations) - 100 elevator final exam questions and answers (verified answers by expert).
3. Exam (elaborations) - Neiep 120-130 multi 2024 questions and answers (verified answers by expert).
4. Exam (elaborations) - Neiep 120-130 multi 2024 questions and answers (verified answers by expert).
5. Exam (elaborations) - Elevator mechanic exam review questions and answers.
6. Exam (elaborations) - Mechanics exam questions and answers (verified answers by expert).
7. Exam (elaborations) - Elevator mechanic exam 2024 questions and answers (verified answers by expert).
8. Exam (elaborations) - Mike-s ultimate mechanics review questions and answers.
9. Exam (elaborations) - Elevator mechanics review questions and answers.
Show more
Mechanic Exam Questions and Answers
(Verified Answers by Expert)
E=__ .- .(correct .answer) .-IR
P=__ .- .(correct .answer) .-IE
Pie .r^2 .= .- .(correct .answer) .-Area .of .a .circle
231 .in^3 ./____ .- .(correct .answer) .-gal.
25.4mm/__ .- .(correct .answer) .-in.
2.2kg/ .- .(correct .answer) .-lb
3 .phase .rectifier .output .= .- .(correct .answer) .-1.33 .x .input
single .phase .output .= .- .(correct .answer) .-0.9 .x .input
RMS .(effective .voltage) .= .- .(correct .answer) .-0.707 .(PEAK .V)
TC .= .- .(correct .answer) .-R .x .C .(5)???
RPM .= .- .(correct .answer) .-60 .(frequency) ./ .(poles/2)
door .overlap .minimum .= .- .(correct .answer) .-5/8" .min
door .gaps .maximum .= .- .(correct .answer) .-3/8" .max
Gibs .minimum .= .- .(correct .answer) .-1/4" .min
Gate .Switch .maximum .= .- .(correct .answer) .-2"
Passenger .Sill .to .Sill .____ .to .______" .- .(correct .answer) .-1/2 .to .1-1/2"
Platform .Lift .Sill .____ .to ._____" .- .(correct .answer) .-3/8" .to .3/4"
, Moving .Walk .maximum .= .- .(correct .answer) .-12 .degree .max
Governors .(Car .Trip .Speed .=______ .& .Overspeed .Switch .=______) .- .(correct .answer) .-
Car .trip .speed .15-20% .greater .than .contract .speed. .
Overspeed .Switch .less .than .or .equal .to .90-95% .of .trip .speed
CWT .(____%) .- .(correct .answer) .-Up .to .10% .greater .than .car .trip .speed
1) .A .contractor .wants .to .raise .the .car .speed .from .100FPM .to .125FPM. .It .currently .has .a .12" .sheave
. .What .size .sheave .is .required? .- .(correct .answer) .-15"
----Diam .= .12, .12"/4=3, .25FPM=3in .: .100FPM .+ .25FPM .= .12"+3" .=15"
2) .An .MOV .
(metal .oxide .varistor) .burns .out. .You .should .replace .it, .but .cannot .read .the .Voltage .or .resistance. .
What .should .you .do? .- .(correct .answer) .-Replace .it .with .a .larger .MOV. .(630)
3) .On .a .Ward-
Leonard .circuit, .the .brake .is .set, .but .the .motor .is .trying .to .slip .through .the .break. .What .circuit .is .th
e .issue? .- .(correct .answer) .-Suicide .Circuit. .(425)
4) .You .have .an .old .DC .motor .and .you .are .adding .an .SCR .Drive. .What .do .you .do .with .the .interpoles
? .- .(correct .answer) .-Leave .the .interpoles .alone. .(425). .
NOTE: .When .adding .the .SCR .Drive .to .the .generator, .the .series .loop .is .removed, .as .are .the .3 .resisto
rs. .Everything .else .stays .the .same.
5) .A .hydro .runs .up .with .no .load, .but .does .not .run .up .with .a .full .load. .What .is .the .issue? .- .
(correct .answer) .-The .relief .valve .is .set .too .low. .(805).
6) .Runby .for .a .1:1 .car .hits .the .CWT .buffer .4" .below .the .top .landing. .The .CWT .runby .should .be .set .
at .18". .How .much .should .the .ropes .be .shortened? .- .(correct .answer) .-
22" .and .for .a .2:1 .with .the .same .issue .--> .44"
7) .You .need .to .work .on .a .freight .door .retiring .cam. .You .LOTO .the .mainline .disconnect, .but .there .is
.still .power .to .the .cam. .What .circuit .is .still .hot? .- .(correct .answer) .-Mainline .disconnect. .(535) .
(3.2.6)
8) .The .contractor .requests .that .the .vertical .center .of .the .rack .and .pinion .hoist .be .moved. .How .is .th
is .accomplished? .- .(correct .answer) .-Adjust .tie .downs/ .wall .ties .(850).