Millwright Test Actual Exam 2024 | Millwright
Exam Update Latest 2024 Questions and
Correct Answers Rated A+
If the seal was not properly aligned or there is excessive wear in some
bearing or shaft______ wear tracks will be the indicator. -ANSWER-
Unusual
For removing hard to remove gasket materials found on sealing surfaces
______ is recommended. -ANSWER-sharpened brass putty knife
Apprenticeship training is -ANSWER-Conducted on the job
Charting alignment on a graph requires a chart that is divided into
thousandths of an inch vertically for the indicator readings and into whole
inches horizontally for the _______ measurements. -ANSWER-Distance
The orthographic drawing may contain a dash or ______ line -ANSWER-
Hidden
In order to shoot through a test object and project an image onto a detector
sheet or film radiography used as a source of penetrating _____. -
ANSWER-Radiation
Which of the following task would you not perform with dividers? -
ANSWER-Measure angles
The over speed trip device is actuated when the turbine reaches a
predetermined limit usually _______ percent above normal full load speed -
ANSWER-10
Positive results in an offset measurement mean that the MTBM is ______
or on the 3 o'clock side -ANSWER-High
,Coupling gap is set and then there is measured -ANSWER-Offset
misalignment
In a hydraulic system movement depends on -ANSWER-Pressure
Fractional dimensions are used on objects ____ -ANSWER-Such as
furniture or utility items
If the cause of the problem is not immediately understood the process of
_____ is often the procedure of choice -ANSWER-Elimination
When applying sealant to the sealing glands flanges keep the sealant away
from the inside edges of the flange by at least _______ inch -ANSWER-
3/16
A stroboscope is triggered by _______ -ANSWER-Transducer
The page of threaded fasteners is measured with a ______ gauge. -
ANSWER-Thread
Liquid penetrant highlights flaws in reveals ______. -ANSWER-Surface
cracks
The tool used to cut external threads on a boat or rod is a____ -ANSWER-
Die
A bill of materials may include information on ______ and other reference
information -ANSWER-Special processes
Engaged gears always have the same ______ -ANSWER-Surface speed
Elevation of equipment is usually found in the -ANSWER-General
arrangements
, Inspect the police rollers in idlers for unevenness or _____ -ANSWER-
Vibrations
When cutting then steel with oxy fuel cutting equipment all the torch say
that the temp is pointing in the direction the torch is traveling at a ______
angle -ANSWER-15-20 degrees
Labyrinth seals work best with materials such as -ANSWER-Grease
Lubrication is the application of any substances that reduces _____ -
ANSWER-Friction
When the dial indicator is mounted on the complex reverse driven coupling
jig the indicator is registered on the ____ -ANSWER-Driver coupling Jig
Pipe should be stored ____ -ANSWER-racks
The most common type of ball bearing is a _____ bearing -ANSWER-
Single deep groove radial
Couplings that are installed after the driver and driven shafts have been
aligned and the equipment has been fastened into position are _____
couplings -ANSWER-Split
When two or more numbers are multiplied to make another number they
are called ______ of the third number -ANSWER-Factors
The continuous reading dial indicator starts at zero and _____ -ANSWER-
Increases clockwise
Vibration with an a specific narrowband range can be detected by _____. -
ANSWER-Electronic filters
Of the following types of O-rings you would select _______ for an
application where temperatures may be -300°F or 500°F -ANSWER-Teflon
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller paulynmugo. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $21.77. You're not tied to anything after your purchase.
