100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
Millwright Test Exam, 213 Questions With 100% Correct Answers 2024. $13.99   Add to cart

Exam (elaborations)

Millwright Test Exam, 213 Questions With 100% Correct Answers 2024.

 1 view  0 purchase
  • Course
  • Institution

Millwright Test Exam, 213 Questions With 100% Correct Answers 2024.

Preview 3 out of 16  pages

  • March 28, 2024
  • 16
  • 2023/2024
  • Exam (elaborations)
  • Questions & answers
avatar-seller
Millwright Test Exam, 213 Questions With 100%
Correct Answers 2024.
If the seal was not properly aligned or there is excessive wear in some bearing or shaft______ wear
tracks will be the indicator.

Unusual

For removing hard to remove gasket materials found on sealing surfaces ______ is recommended.

sharpened brass putty knife

Apprenticeship training is

Conducted on the job

Charting alignment on a graph requires a chart that is divided into thousandths of an inch vertically for
the indicator readings and into whole inches horizontally for the _______ measurements.

Distance

The orthographic drawing may contain a dash or ______ line

Hidden

In order to shoot through a test object and project an image onto a detector sheet or film radiography
used as a source of penetrating _____.

Radiation

Which of the following task would you not perform with dividers?

Measure angles

The overspeed trip device is actuated when the turbine reaches a predetermined limit usually _______
percent above normal full load speed

10

Positive results in an offset measurement mean that the MTBM is ______ or on the 3 o'clock side

High

Coupling gap is set and then there is measured

Offset misalignment

In a hydraulic system movement depends on

Pressure

Fractional dimensions are used on objects ____

,Such as furniture or utility items

If the cause of the problem is not immediately understood the process of _____ is often the procedure
of choice

Elimination

When applying sealant to the sealing glands flanges keep the sealant away from the inside edges of
the flange by at least _______ inch

3/16

A stroboscope is triggered by _______

Transducer

The page of threaded fasteners is measured with a ______ gauge.

Thread

Liquid penetrant highlights flaws in reveals ______.

Surface cracks

The tool used to cut external threads on a boat or rod is a____

Die

A bill of materials may include information on ______ and other reference information

Special processes

Engaged gears always have the same ______

Surface speed

Elevation of equipment is usually found in the

General arrangements

Inspect the police rollers in idlers for unevenness or _____

Vibrations

When cutting then steel with oxy fuel cutting equipment all the torch say that the temp is pointing in
the direction the torch is traveling at a ______ angle

15-20 degrees

Labyrinth seals work best with materials such as

Grease

Lubrication is the application of any substances that reduces _____

Friction

, When the dial indicator is mounted on the complex reverse driven coupling jig the indicator is
registered on the ____

Driver coupling Jig

Pipe should be stored ____

racks

The most common type of ball bearing is a _____ bearing

Single deep groove radial

Couplings that are installed after the driver and driven shafts have been aligned and the equipment
has been fastened into position are _____ couplings

Split

When two or more numbers are multiplied to make another number they are called ______ of the
third number

Factors

The continuous reading dial indicator starts at zero and _____

Increases clockwise

Vibration with an a specific narrowband range can be detected by _____.

Electronic filters

Of the following types of O-rings you would select _______ for an application where temperatures
may be -300°F or 500°F

Teflon

Special cleaning tips for cutting of bald head in notes is called a _______ tip

Rivet cutting

PCVs limit and regulate the _____ in the system

Pressure

The total distance that the chef travels from one piece to the other during one vibration cycle is the
_____.

Displacement

A positive- contact seal generally used on cylinder pistons is the ______ seal

Cup

Equipment reference points are marked with

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller LectDan. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for $13.99. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

67096 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy study notes for 14 years now

Start selling
$13.99
  • (0)
  Add to cart