100% satisfaction guarantee Immediately available after payment Both online and in PDF No strings attached
logo-home
ARMY ELECTRICAL EXPLOSIVES SAFETY (AMMO28) EXAM LATEST ACTUAL EXAM 120+ QUESTIONS AND CORRECT DETAILED ANSWERS |ALREADY GRADED A+ $23.58   Add to cart

Exam (elaborations)

ARMY ELECTRICAL EXPLOSIVES SAFETY (AMMO28) EXAM LATEST ACTUAL EXAM 120+ QUESTIONS AND CORRECT DETAILED ANSWERS |ALREADY GRADED A+

 1 view  0 purchase
  • Course
  • Institution

ARMY ELECTRICAL EXPLOSIVES SAFETY (AMMO28) EXAM LATEST ACTUAL EXAM 120+ QUESTIONS AND CORRECT DETAILED ANSWERS |ALREADY GRADED A+ ARMY ELECTRICAL EXPLOSIVES SAFETY (AMMO28) EXAM LATEST ACTUAL EXAM 120+ QUESTIONS AND CORRECT DETAILED ANSWERS |ALREADY GRADED A+ ARMY ELECTRICAL EXPLOSIVE...

[Show more]

Preview 3 out of 26  pages

  • January 2, 2024
  • 26
  • 2023/2024
  • Exam (elaborations)
  • Questions & answers
avatar-seller
ARMY ELECTRICAL EXPLOSIVES SAFETY (AMMO28)
EXAM LATEST 2023-2024 ACTUAL EXAM 120+
QUESTIONS AND CORRECT DETAILED ANSWERS
|ALREADY GRADED A+
At a minimum, how many individual resistance tests must be performed on this
conductive floor? Refer to DA PAM 385-64, Section C-3 as required. - ANSWER--
Ten tests: five electrode-to-electrode and five electrode-to-ground tests


An LPS requires three-point fall-of-potential earth resistance testing every -
ANSWER--Every 24 months


When conducting a 3-point fall-of-potential earth resistance test, what is the
maximum allowable resistance reading? - ANSWER--25 ohms


When conducting a bonding resistance test, what is the maximum allowable
reading? - ANSWER--1 ohm


How many individual bonding resistance tests are required on an integral LPS with
12 air terminals and 2 down conductors? - ANSWER--24


Which storm warning system measures the strength of atmospheric electric fields
and warns of the possibility of lightning strikes? - ANSWER--Pre-strike


Which hazardous classified location division poses the least probability of ignition
or explosion? - ANSWER--Division 2


Which material belongs to hazardous classified location Class II? - ANSWER--coal
dust

, ARMY ELECTRICAL EXPLOSIVES SAFETY (AMMO28)
EXAM LATEST 2023-2024 ACTUAL EXAM 120+
QUESTIONS AND CORRECT DETAILED ANSWERS
|ALREADY GRADED A+

Which material belongs to hazardous classified location Class I? - ANSWER--
acetylene gas


Which HERO classification describes items that may explode or detonate if
exposed to EMR? - ANSWER--HERO UNSAFE


Which of the following is NOT a hazard posed by electromagnetic radiation? -
ANSWER--WRONG ignition of fuel and other combustibles


How many feet radius does the DoD require for an LPS zone of protection? -
ANSWER--100 ft


Which statement regarding lightning protection is false? - ANSWER--lightning
protection system prevents lightning strikes from occurring.


While conducting an LPS inspection, you discover the scenario illustrated in the
image below. Do you write it up as a discrepancy? Why or why not? - ANSWER--
Yes, because the air terminal is not attached to a conductor.


How many down conductors are required for a mast LPS? - ANSWER--WRONG 4
WRONG 3


Which material is preferred for ground conductors? - ANSWER--Copper

, ARMY ELECTRICAL EXPLOSIVES SAFETY (AMMO28)
EXAM LATEST 2023-2024 ACTUAL EXAM 120+
QUESTIONS AND CORRECT DETAILED ANSWERS
|ALREADY GRADED A+

What does n represent in the Basic Bonding Formula? - ANSWER--Number of
down conductors


What does Km represent in the Basic Bonding Formula? - ANSWER--WRONG
Height of the proposed bond


During an LPS inspection you notice a grounded metal pipe 3 feet from a
conductor. Should you write it up as a possible discrepancy? - ANSWER--Yes.
Grounded metal objects within 6 feet of a conductor should be considered for
bonding


What does D represent in the Basic Bonding Formula? - ANSWER--Bonding
distance


Which bonding condition applies to isolated metal objects surrounded by non-
conductive material (such as a metal door frame in a concrete wall)? - ANSWER--
WRONG Condition 2


Calculate the BBF to determine if bonding is required for the scenario below. Use
a calculator, the BBF equation aid, and the bonding job aid as required.
• The metal vent is 15 feet high.
• There are 2 down conductors at the proper spacing.
• The vent is 12 inches (1 foot) from a conductor through air. - ANSWER--Bonding
distance for the metal roof vent is 1 foot 8 inches. Bonding is required.

The benefits of buying summaries with Stuvia:

Guaranteed quality through customer reviews

Guaranteed quality through customer reviews

Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.

Quick and easy check-out

Quick and easy check-out

You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.

Focus on what matters

Focus on what matters

Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!

Frequently asked questions

What do I get when I buy this document?

You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.

Satisfaction guarantee: how does it work?

Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.

Who am I buying these notes from?

Stuvia is a marketplace, so you are not buying this document from us, but from seller erickarimi. Stuvia facilitates payment to the seller.

Will I be stuck with a subscription?

No, you only buy these notes for $23.58. You're not tied to anything after your purchase.

Can Stuvia be trusted?

4.6 stars on Google & Trustpilot (+1000 reviews)

79064 documents were sold in the last 30 days

Founded in 2010, the go-to place to buy study notes for 14 years now

Start selling
$23.58
  • (0)
  Add to cart