NACE CIP 1 CBT EXAM PRACTICE
QUESTIONS | 189 Questions with 100%
Correct Answers | Updated & Verified
Dew point is the temperature at which - -condensation occurs.
-You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank
lining is being applied. After application of the 19 coat you notice small blisters in some
areas of the applied lining. Your FIRST preferred course of action is to: - -Document the
problem and advise the Contractor and Owner's representative.
-If a contractor is using a poorly maintained compressor to supply air for abrasive blast
cleaning and conventional airspray, the coating inspector should perform a - -blotter
test for the presence of oil and water.
-Upon arrival of coating materials, the inspector should - -observe and document the
amount of material and batch numbers.
-Relative humidity is - -a measure of the amount of moisture in the air compared to
saturation level.
-Galvanic corrosion occurs on which of the following substrates? - -Metal
-When applying Thermal Spray Coatings the specification is most likely to reference: - -
SSPC-CS 23.00/AWS C2.23/NACE No. 12
-What is the minimum recommended distance away from an edge that an inspector
should take a measurement with a dial type magnetic pull off Dry Film Thickness(DFT)
gauge? - -2.5 cm (1 inch)
-Polymerization is the process of? - -Monomers joining together.
-An exposed area of the substrate or previous coat of a conductive material, often
caused by poor application technique is called: - -Holiday
-Checking is: - -a fine crack in the surface of a coating that rarely reaches the substrate.
-Inspection documentation is important because: - -Owners use the documentation for
a variety of purposes.
-An Inspectors personal log book should contain: - -No comments regarding the
application team.
-You have just received your NACE CIP Level 1 certification when you are asked to
supervise a team of uncertified field pipeline inspectors. Your FIRST preferred course of
action is to: - -Review the NACE Attestation prior to making a decision.
, -Good record can provide maintenance departments with detailed information about
ALL of the following EXCEPT: - -How the item was coated.
-Non Conformance Reports are completed by the Inspector: - -When the Inspector and
Contractor deem it to be significant non conforming item.
-The initial steel condition is important to the NACE Inspector because: - -The
Inspector may have to reject the steel.
-The form of corrosion that has the largest potential for unexpected catastrophic failure
is: - -Galvanic Corrosion
-What is used to determine compressed air cleanliness? - -Profilometer
-Osmotic blistering is most likely to occur as a result of: - -Airless spray application.
-When performing tests for oil and grease using an ultra violet light, the NACE
Inspector should be aware that: - -Synthetic oil or grease may not be identified.
-To achieve consistently accurate results with ALL alt test equipment: - -wash your
hands before sampling.
-When holiday testing is required the Inspector is always required to enforce what
standard? - -NACE SP 0188
-If the specifier does not identify a restriction level in accordance with SSPC PA 2, the
default restriction level is: - -Level 3
-Fine cracks in the surface of a coating that rarely reach the substrate are called: - -
Checking
-It is good practice for the NACE Inspector to have instrument calibration certificates
available: - -At all times.
-In a non convertible coating the role of the primary solvent is to: - -To control the
evaporation rate.
-Removal of weld splatter is required: - -When specifically identified in the owners
specification.
-Common errors that may produce inaccurate readings when using a Dial Type
Magnetic Pull Off Dry Film Thickness(DFT) gauge include: - -Failing to determine the
Base Metal Reading(BMR),Rotating the dial too fast when taking measurements, and
Measuring ditty, tacky, or soft films.
-Conventional spray us good choice when: - -High quality finishes are required.
-Which of these tests uses a syringe? - -Bresle Patch
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Nurselucy2023. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $8.49. You're not tied to anything after your purchase.
