Exam (elaborations)
ASNT VT Level II Exam Questions With 100% Correct Answers.
- Course
- Institution
ASNT VT Level II Exam Questions With 100% Correct Answers.
[Show more]
Content preview
ASNT VT Level II Exam Questions With 100% Correct Answers.1. Localized education in an area of a bolt that is under overload conditions is referred to as?
A. Sizing B. Necking Down
C. Erosion
D. Elongation Answer - b
2. The least common location for fastener failure is?
A. In the head to shank fillet.
B. Throughout the first thread inside the nut on threaded fasteners.
C. In the mid grip.
D. At the transition from the thread to the shank. Answer - c
3. Discontinuities that are produced during the hot or cold working of the ingot into rod or bar to make studs are called?
A. Inherent discontinuities.
B. Primary processing discontinuities.
C. Secondary processing discontinuities. D. Service-induced discontinuities. Answer - b
4. Service-induced discontinuities in bolting systems may be produced by?
A. Vibration.
B. Over-tensioning
C. Corrosion
D. All of the about Answer - d
5. The fillet weld size is based on the?
A. Effective fillet weld throat.
B. Length of fillet weld.
C. Theoretical throat.
D. Length of fillet weld leg. Answer - d
6. A convex weld surface?
A. Curves inward.
B. Curves outward.
C. Contains a hollow.
D. Does both a and c above. Answer - b
7. During the solidification of metal, a hole produced due to escaping gases is called a?
A. Burst B. Cold shut.
C. Flaking.
D. Blow hole. Answer - d
8. Weldments might contain?
A. Shrinkage.
B. Incomplete penetration.
C. Seams.
D. Laps. Answer - b
9. A discontinuity typically found in forgings is?
A. Shrinkage.
B. Bleed-out.
C. Laps
D. Undercut. Answer - c
10. Embrittlement, caused by a physical or chemical change in the metal, is a reduction in?
A. Ductility.
B. Hardness.
C. Hydrogen.
D. All of the above. Answer - a
11. The deterioration of metal by chemical or electrochemical reaction with its environment is called?
A. Corrosion.
B. Erosion.
C. IGSCC.
D. None of the above. Answer - a
12. The roughest surface finish is indicated by a measurement of?
A. 64uin.
B. 150uin.
C. 250uin.
D. 380uin. Answer - d
13. A basic metallurgical joint configuration that is used for complete joint penetration
is called?
A. a butt joint.
B. a fillet joint.
C. a lap joint.
D. none of the above. Answer - a
19. The gage that provides measurements of internal misalignment on 76 mm (3in.) diameter pipe is?
A. a Cambridge gage.
B. a fillet weld gage.
C. a hi-lo welding gage.
D. both a and b above. Answer - c
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller EvaTee. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $12.99. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
79373 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now