Dew point is the temperature at which - answercondensation occurs.
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank
lining is being applied. After application of the 19 coat you notice small blisters in
some areas of the applied lining. Your FIRST preferred cours...
NACE CIP 1 CBT EXAM PRACTICE QUESTIONS
AND ANSWERS (COMPLETED)
Dew point is the temperature at which - answercondensation occurs.
You are the NACE Inspector on a tank lining project where a 50% solids epoxy tank
lining is being applied. After application of the 19 coat you notice small blisters in some areas of the applied lining. Your FIRST preferred course of action is to: - answerDocument the problem and advise the Contractor and Owner's representative.
If a contractor is using a poorly maintained compressor to supply air for abrasive
blast cleaning and conventional airspray, the coating inspector should perform a - answerblotter test for the presence of oil and water.
Upon arrival of coating materials, the inspector should - answerobserve and document the amount of material and batch numbers.
Relative humidity is - answera measure of the amount of moisture in the air compared to saturation level.
Galvanic corrosion occurs on which of the following substrates? - answerMetal
When applying Thermal Spray Coatings the specification is most likely to reference: - answerSSPC-CS 23.00/AWS C2.23/NACE No. 12
What is the minimum recommended distance away from an edge that an inspector should take a measurement with a dial type magnetic pull of Dry Film Thickness(DFT) gauge? - answer2.5 cm (1 inch)
Polymerization is the process of? - answerMonomers joining together.
An exposed area of the substrate or previous coat of a conductive material, often caused by poor application technique is called: - answerHoliday
EXAM NACE CIP 1 CBT EXAM PRACTICE QUESTIONS
AND ANSWERS (COMPLETED)
Checking is: - answera fine crack in the surface of a coating that rarely reaches the substrate.
Inspection documentation is important because: - answerOwners use the documentation for a variety of purposes.
An Inspectors personal log book should contain: - answerNo comments regarding the application team.
You have just received your NACE CIP Level 1 certification when you are asked to supervise a team of uncertified field pipeline inspectors. Your FIRST preferred course of action is to: - answerReview the NACE Attestation prior to making a decision.
Good record can provide maintenance departments with detailed information about ALL of the following EXCEPT: - answerHow the item was coated.
Non Conformance Reports are completed by the Inspector: - answerWhen the Inspector and Contractor deem it to be significant non conforming item.
The initial steel condition is important to the NACE Inspector because: - answerThe Inspector may have to reject the steel.
The form of corrosion that has the largest potential for unexpected catastrophic failure is: - answerGalvanic Corrosion
What is used to determine compressed air cleanliness? - answerProfilometer
Osmotic blistering is most likely to occur as a result of: - answerAirless spray application.
EXAM NACE CIP 1 CBT EXAM PRACTICE QUESTIONS
AND ANSWERS (COMPLETED)
When performing tests for oil and grease using an ultra violet light, the NACE Inspector should be aware that: - answerSynthetic oil or grease may not be identified.
EXAM NACE CIP 1 CBT EXAM PRACTICE QUESTIONS
AND ANSWERS (COMPLETED)
To achieve consistently accurate results with ALL alt test equipment: - answerwash your hands before sampling.
When holiday testing is required the Inspector is always required to enforce what standard? - answerNACE SP 0188
If the specifier does not identify a restriction level in accordance with SSPC PA 2, the default restriction level is: - answerLevel 3
Fine cracks in the surface of a coating that rarely reach the substrate are called: - answerChecking
It is good practice for the NACE Inspector to have instrument calibration certificates available: - answerAt all times.
In a non convertible coating the role of the primary solvent is to: - answerTo control the evaporation rate.
Removal of weld splatter is required: - answerWhen specifically identified in the owners specification.
Common errors that may produce inaccurate readings when using a Dial Type Magnetic Pull Of Dry Film Thickness(DFT) gauge include: - answerFailing to determine the Base Metal Reading(BMR),Rotating the dial too fast when taking measurements, and Measuring ditty, tacky, or soft films.
Conventional spray us good choice when: - answerHigh quality finishes are required.
Which of these tests uses a syringe? - answerBresle Patch
EXAM
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller BestKey. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $12.00. You're not tied to anything after your purchase.
