Within how many days of an inspection are you required to submit the new boat inspection report correct answer: 10
List the six basic safety procedures to follow when troubleshooting or repairing electrical components correct answer: 1. Never operate, repair, adjust, tamper with equipment unle...
MKC SWE study (in progress)| 302 QUESTIONS|
WITH COMPLETE SOLUTIONS
Within how many days of an inspection are you required to submit the new boat inspection report correct answer: 10
List the six basic safety procedures to follow when troubleshooting or repairing electrical components correct answer: 1. Never operate, repair, adjust, tamper with equipment unless assigned to do so. 2. obey all posted operating and safety precautions 3. de-energize equipment prior to repair. 4. always wear approved PPE.
5. use insulated tools and non-metalic flashlight. 6. tighten the connections of fremovable tes leads on portable meters.
generally the crown end of the piston is slightly smaller in diameter than the skirt for what reason correct answer: to allow for expansion and proper fit
piston ring gaps should be staggered at _ degrees to reduce gas leakage correct answer: 180*
what could happen if you ignore the specific safety warning in the engine service manual correct answer: injure yourself/people on or around the boat/damage outboard engine
a placard stating discharge of oil prohibited must be posted on all vessels more than __ feet in length correct answer: 26 what CFR regulations identifies prohibited spaces where oil and hazardous material are not to be stored correct answer: 33CFR155.470
what is the standard maximum ambient operating temperature for compressor drive motors correct answer: 104*F
in the vacuum gravity system, what part houses a set of inclined absorption plates correct answer: vacuum gravity vessel
what filter element in an OWS is used to remove small particles such as shaving and dirt from the oily water mixture correct answer: pre-filter
before working on or removing any parts of the air compressor, you should make sure the following conditions are completed correct answer: the compressor is completely blown down and the pressure is relieved
before and during the operation of the R/O what type of general inspection should be conducted correct answer: make sure the flowmeters are clear and floats are visable
which safety precaution should be observed during R/O operation correct answer: make sure all pressure relief valves dischards are unobstructed and the release fluid is conducted to low pressure area clear of personnel
what are the three effects of excessively worn rudder shaft bearings correct answer: 1. imprecise and poor steering response 2.excessive vibration 3. leakage through the rudder post housing
what component registers cumulative volume in gallons of permeate being produced by the R/O unit and being used by the ship correct answer: Totalizing flow meter
normally a diesel engine start air bank has a minimum capacity for how many cold and hot starts correct answer: 1 cold and 9 hot
when conducting performance test, engines should be operated at what percentage of coat guard load correct answer: 80-90%
the ODR facilitates what type of operating data correct answer: 1. trend recording
2. event recording
3. dynamic recording
4. alarm recording
5. trip recording
what are the effects of a damaged propeller correct answer: 1. lack of power
2. high fuel consumption 3. unexpected vibration
high pressure pump creates ___ to____ PSI achieve reverse osmosis correct answer: 700-1000 PSI
pulsation dampener absorbs pulsations created on the discharge side of a high pressure pump consisting of nitrogen charged rubber bladder charged to approximately correct answer: 2/3 system pressure
If the low pressure switch predetermined setting isn't met (on 110's it is 5 psi) correct answer: low pressure switch secures the
high pressure pump
list the possible causes of low or variable cylinder compression correct answer: 1. damaged head gasket
2. damaged pistons
3. broke or stuck piston rings
4. scored cylinder walls
5. stuck valves (four stroke)
6. Incorrectly adjusted valves(four stroke)
what are the three main areas of concern when troubleshooting a
hard starting engine? correct answer: 1. ignition
2.fuel
3. compression
what are the seven primary indicators for completing DEMPs? correct answer: 1. cylinder compression pressure
2.cylinder firing pressure
3.cylinder exhaust temperature
4. crankcase vacuum
5. intake manifold pressure
6. exhaust back-pressure
7. L/O consumption
ODR will record data automatically for all files under what circumstances correct answer: as long as ODR is turned on
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller Classroom. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $12.99. You're not tied to anything after your purchase.
