Class notes
Concrete Structures Study Notes - CVEN3304 - UNSW
- Course
- Institution
Full set of notes for CVEN3304.
[Show more]
Seller
Follow
callumfisher
Content preview
CVEN3304 Study NotesTrimester 2, 2019
INTRODUCTION TO CONCRETE
• In its simplest form, concrete consists of a binder (cement) and filler
(aggregate)
• Around 33 billion tonnes of concrete is used globally per year, this is the
highest volume of any material used by humans other than water
• An accelerating trend of 3D printing of concrete has emerged in recent years
• The four key areas of concrete performance as a material:
o Environmental Concern
o Energy Consumption
o Cost
o Physical Performance
• Concrete has a Green Degree of around 1.042, which indicates that the
theoretical usage of natural resources is actually higher than that of the actual
usage for concrete (eco-friendly)
• General advantages of concrete include:
o Durability
o Low cost
o Formed on site
o Energy efficient
o Non-flammable
o Thermal resistance
o Water resistance
o Aesthetics
• General disadvantages of concrete include:
o Brittle
o Slow strength development
o Low strength/mass ratio
o Volume instability
o Low strength in tension
HISTORY OF CONCRETE
• Egyptians used an ancient form of concrete in the Great Pyramids, using
gypsum and straw as a binding agent
• Ancient Romans used mortar combining volcanic ash and lime to build
structures (Pozzolana cement)
• Joseph Aspdin developed Portland cement in 1824, which is still the most
commonly used recipe used in concrete structures today
• The main areas of research for improvement of concrete is as follows:
o Reducing CO2 emissions during production
o Increasing energy efficiency during production
o Controlling physical properties on a nanoscale
,CONSTITUENTS OF CONCRETE
• The main components of concrete are:
o Cement (10% volume)
o Fine Aggregate (32% volume)
o Coarse Aggregate (40% volume)
o Water (14% volume)
o Chemical additives
• Mortar is composed of cement, water and fine aggregate – which combines to
form a binding property for the concrete
• Whilst cement only makes up around 10% of the concrete volume, it often
accounts for up to 2/3rds of the cost of production
CEMENT
• Originally, a stationary kiln was used to produce Portland cement
• The far superior rotary kiln is a rotating device which burns raw materials to
create cement
• The key oxides used to produce cement include:
o Lime (CaO) – 65% by weight
o Iron (Fe2O3) – 5% by weight
o Silica (SiO2) – 20% by weight
o Alumina (Al2O3) – 5% by weight
• In the study of cement, an abbreviated notation system is typically used to
indicate various oxides (known as cement notation)
o C = CaO
o S = SiO2
o A = Al2O3
o F = Fe2O3
o S = SO3
o H = H2O
• Before entering the kiln, all raw limestone and clay is grinded and
homogenized
• A wet-process kiln is large and provides inefficient transfer of heat
o The raw cement materials were blended into a slurry consisting of
around 40% water
• A dry-process kiln is much smaller and provides greater transfer of heat to
the raw materials
o For centuries, it was considered more difficult to get dry powders to
blend adequately to produce clinker
o In the dry-process kiln, the blended raw materials are processed
beforehand in a pre-heating tower
o Excess heat energy from the kiln is funnelled into this tower, which
sends ‘cyclones’ of air through the raw materials to evaporate moisture
• Clinker is the output material from a kiln, which is usually one of the key
cement oxides with a bonded metal ion
o Before entering the kiln, the dominant compounds include limestone,
quartz, clay and iron oxides
, o After heating up to around 1450 degrees Celsius, the dominant
compounds include Alite and Bellite
o After being in the kiln, the alite is stabilised through rapid cooling
• Gypsum (CSH2) is hydrated calcium sulfate, which is added to clinker in
order to prevent flash set of concrete (rapid forming of rigidity and heat)
• The clinker is then grinded to increase surface area, where the normal surface
area is around 350m2/kg
• There are 7 standard recipes for cement given in Australia by the
AS3972-2010 standards, separated into two categories:
o General Purpose
o Special Purpose
• There are several thermal zones within the kiln (from front to back):
o Dehydration zone – the entrance of the kiln where all remaining
moisture is removed from the material
o Calcination zone – free lime, bellite and aluminates are formed
through the decarbonation reaction (CaCO2 > CaO + CO2)
o Transition zone – gradual increase in bellite (C2S) proportion as the
heat increases rapidly
o Clinkering zone – allows for production of allite (C3S)
o Cooling zone – temperature drops rapidly once the clinker has moved
past the bottom of the kiln, forming C3A (aluminate) and C4AF
(ferrite)
HYDRATION OF CEMENT
• Hydration is a loose term describing the reactions that occur between
Portland cement and water particles
• The two chemical processes occurring during the hydration of cement:
o Dissolution
o Precipitation
• During dissolution, the Portland cement grains dissolve and separate within
the water
• Through precipitation, the cement grains react with the water to form a layer
of hydration products
• The extent to which the hydration process has occurred can be monitored by
measuring the heat energy given off, since this is an exothermic reaction (this
usually plateaus after around 3 days)
• The four stages of hydration of cement in terms of heat energy:
o Rapid heat evolution – less than 15 mins
▪ CH and ettringite are formed
o Dormant period (very low heat energy) - 1-3 hours
▪ CH, ettringite and CSH products form
o Accelerating stage – 3-8 hours
▪ CSH products rapidly form
o Decelerating stage – 12-24 hours
▪ Full range of products are slowly produced
The benefits of buying summaries with Stuvia:
Guaranteed quality through customer reviews
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
Quick and easy check-out
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Focus on what matters
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
Frequently asked questions
What do I get when I buy this document?
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Satisfaction guarantee: how does it work?
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Who am I buying these notes from?
Stuvia is a marketplace, so you are not buying this document from us, but from seller callumfisher. Stuvia facilitates payment to the seller.
Will I be stuck with a subscription?
No, you only buy these notes for $9.99. You're not tied to anything after your purchase.
Can Stuvia be trusted?
4.6 stars on Google & Trustpilot (+1000 reviews)
67096 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now