Stationary Engineer Exam Bundle With Complete Solutions 100% Verified

upStationary Grade 3 Engineering License Exam Questions And Answers 100% Solved how can you loose your license? - answer1) drinking on the job 2) sleeping on the job 3) negligence 4) unsafe work 5) signing a falsified license application for someone 6) failing to renew your license annually ...

1st Class Stationary Engineers Examination Questions And Answers 100% Solved Deaerator - answerA Device used to remove oxygen from boiler feedwater The term "quality of steam" has to do with steams - answerMoisture content A sleeve is used on the shaft of a centrifugal pump to - answerProtect ...

1st Class Stationary Engineers Examination Questions And Answers 100% Solved when is it best to replace the manhole gasket - answereach year after cleaning the inside of the boiler When riveting boiler plate it is most important to - answerget the proper pitch between the rivets A vapor heatin...

Stationary Engineer Exam Questions And Answers 100% Solved What is a water tube boiler? What are five of the advantages & disadvantages of a water tube boiler? Name four types of water tube boilers. - answerIn a water tube boiler the products of combustion pass around the tubes containing boile...

Stationary Engineer Electric Exam Questions With 100% Correct Answers An AC circuit consists only of a pure inductance and a power source. The relationship between the voltage and the current in this circuit is that the - answercurrent lags the voltage The power factor of a load is equal to the ...

Stationary Engineering Exam Questions And Answers 100% Solved The Main function of a steam separator in a steam power plant is to - answerincrease steam quality The MAIN purpose of a dip tube in a low-pressure hot water system is to - answerprevent air from entering the main The rating of a un...

Stationary Engineering Test Exam Questions And Answers 100% Solved When designing a boiler, special consideration must be given to heat transmission - answerRadiation, conduction, and convection Which type of heat transfer takes place by actual physical contact, from molecule to molecule, witho...

Stationary Engineer License Exam Prep Questions And Answers 100% Solved A ______ fuse is necessary for a circuit with a load of 21,000 watts and a voltage of 220 volts. A. 100 B. 150 C. 175 D. 200 A. 100 amps. Note: V = IR Therefore I = V/R 21,000 amps /220 volts = 95 amps At 0 psig, how ma...

Stationary Engineering Chapter 1 Exam ___ is a pushing or pulling motion and is commonly measured in pounds. - answerForce The amount of work performed is the ___ of the force and distance moved. - answerproduct ___ is the heat required to change the state of 1 lb of a substance from a solid to a...

Stationary engineering lic prep Exam Questions And Answers Wire drawing - answerDifference in pressure going from a large volume to a smaller volume Continuous blowdown - answerUsed for the removal of surface impurities on the boilers water surface Why are stays used on flat surfaces not round?...

Stationary Engineering Exam Questions And Answers 100% Solved In a reciprocating feedwater pump, the _______________ A. water piston is larger than the steam piston B. water and steam piston are the same size C. steam piston is larger than the water piston D. steam valve has to be as large as ...

MD Stationary Engineer Exam Questions And Answers Gases of Combustion that cool on Contact with the boiler heating Surface before combushion is completed Cause a(n) _________ - answerFormation of soot and smoke In the event of a flame failure, the programmer will______ - answerSecure the fuel, p...

Stationary Engineering Exam Questions And Answers 100% Solved What is the pressure at the base of a vertical foot of water? - answer0.433 psi How much should the boiler pressure increase when performing a hydrostatic test? - answer1.5 times the safety valve setting The range of a boiler steam p...

Stationary Engineering Exam Questions And Answers 100% Solved There must be adequate ___ across any steam trap for the condensate and/or air to be removed from the steam system. differential pressure When 200 lb of water is heated from 62°F to 75°F, ___ Btu is absorbed. 2600 A(n) ___ is use...