Millwright Exam 1 |100questions| Correct Answers COMPLETE FULL SOLUTION PACK EXAM BUNDLE!!!Millwright Exam 1 |100questions| Correct Answers COMPLETE FULL SOLUTION PACK EXAM BUNDLE!!!Millwright Exam 1 |100questions| Correct Answers COMPLETE FULL SOLUTION PACK EXAM BUNDLE!!!Millwright Exam 1 |100q...
[Show more]
What is the fire triangle? a. Wood, coal, combustibles b. Heat, fuel, oxygen c. Class A, B, C d. Green triangle, blue circle, red square - ANSWER b. Heat, fuel, oxygen Whose responsibility is it for you to wear Protective equipment in good order? a. Your own b. Plant manager c. Manufac...
Preview 1 out of 4 pages
Add to cartWhat is the fire triangle? a. Wood, coal, combustibles b. Heat, fuel, oxygen c. Class A, B, C d. Green triangle, blue circle, red square - ANSWER b. Heat, fuel, oxygen Whose responsibility is it for you to wear Protective equipment in good order? a. Your own b. Plant manager c. Manufac...
Compared to fibre core, IWRC tends to be _______ resilient and less capable of absorbing shock loads a. more b. less c. equally d. slightly more - ANSWER b. less What rope is considered to be a standard wire a. Lang lay b. right regular lay c. left regular lay d. performing lay - ANSWER ...
Preview 2 out of 10 pages
Add to cartCompared to fibre core, IWRC tends to be _______ resilient and less capable of absorbing shock loads a. more b. less c. equally d. slightly more - ANSWER b. less What rope is considered to be a standard wire a. Lang lay b. right regular lay c. left regular lay d. performing lay - ANSWER ...
1. When the downward force at C2 is 100 lb and D2 = 2.5 inches, the upward force at C1 will be ________lb if D1 = 4 inches. A. 160 B. 256 C. 384 D. 240 - ANSWER A. 160 x/12.56 sq in = 100 lbs/7.85 sq in x = (100lbs/7.85 sq in)12.56 x = 160 lbs 2. Add the following decimals and expres...
Preview 2 out of 7 pages
Add to cart1. When the downward force at C2 is 100 lb and D2 = 2.5 inches, the upward force at C1 will be ________lb if D1 = 4 inches. A. 160 B. 256 C. 384 D. 240 - ANSWER A. 160 x/12.56 sq in = 100 lbs/7.85 sq in x = (100lbs/7.85 sq in)12.56 x = 160 lbs 2. Add the following decimals and expres...
1. Of a block and tackle with five rope falls and minimum friction, how much force is needed to retain 250lbs? a. 50 lbs b. 100 lbs c. 250 lbs d. 75 lbs - ANSWER a. 50 lbs 250lbs/5 = 50 lbs 2. What diameter rope is needed to support two tons using a vertical lift? a. ½" b. ¾" c...
Preview 2 out of 9 pages
Add to cart1. Of a block and tackle with five rope falls and minimum friction, how much force is needed to retain 250lbs? a. 50 lbs b. 100 lbs c. 250 lbs d. 75 lbs - ANSWER a. 50 lbs 250lbs/5 = 50 lbs 2. What diameter rope is needed to support two tons using a vertical lift? a. ½" b. ¾" c...
The breaking strength of rope is a. force needed to pull rope b. force needed to tear rope c. force needed to break the rope d. force needed to stretch rope - ANSWER c. force needed to break the rope Traction grade wire rope has a breaking load of __________ tons per square inch a. 110-190 ...
Preview 2 out of 11 pages
Add to cartThe breaking strength of rope is a. force needed to pull rope b. force needed to tear rope c. force needed to break the rope d. force needed to stretch rope - ANSWER c. force needed to break the rope Traction grade wire rope has a breaking load of __________ tons per square inch a. 110-190 ...
A millwright is a tradesperson who build, installs, and maintains machinery. - ANSWER True ____________________ is the process of reducing and shaping materials using power tools. - ANSWER Machining Pharmaceuticals and aerospace are examples of two industries in which UBC millwrights work. - A...
Preview 3 out of 16 pages
Add to cartA millwright is a tradesperson who build, installs, and maintains machinery. - ANSWER True ____________________ is the process of reducing and shaping materials using power tools. - ANSWER Machining Pharmaceuticals and aerospace are examples of two industries in which UBC millwrights work. - A...
On a pedestal grinder, the gap between the grinding wheel and work rest should not exceed: - ANSWER 1/8 inch The kind of abrasive material used in grinding wheels for general purpose applications is: - ANSWER aluminum oxide A blotter is used on a grinding wheel to: - ANSWER protect the flanges...
Preview 3 out of 21 pages
Add to cartOn a pedestal grinder, the gap between the grinding wheel and work rest should not exceed: - ANSWER 1/8 inch The kind of abrasive material used in grinding wheels for general purpose applications is: - ANSWER aluminum oxide A blotter is used on a grinding wheel to: - ANSWER protect the flanges...
Which of the following best describes a free flow control valve? A) It is the simplest form of directional control allowing flow in one direction only B) They are used to prevent a load suspended by a cylinder from free fall C) They operate actuators at different times D) They make a humming sou...
Preview 3 out of 20 pages
Add to cartWhich of the following best describes a free flow control valve? A) It is the simplest form of directional control allowing flow in one direction only B) They are used to prevent a load suspended by a cylinder from free fall C) They operate actuators at different times D) They make a humming sou...
NCCER was created to - ANSWER Award a college degree for completion of the NCCER Standardized Curricula The purpose of NCCER's Registry is to. - ANSWER Provide industry-wide credential and assure national portability of skills. Two of the more important traits of the professional Millwright a...
Preview 1 out of 2 pages
Add to cartNCCER was created to - ANSWER Award a college degree for completion of the NCCER Standardized Curricula The purpose of NCCER's Registry is to. - ANSWER Provide industry-wide credential and assure national portability of skills. Two of the more important traits of the professional Millwright a...
1. How is efficiency found? A) output over input B) input over output C) output times input times 100 D) output times input divided by hp - ANSWER A) Output over input 2. What is the maximum capacity in kg of a heavy duty ladder? A) 136 B) 113 C) 102 D) 91 - ANSWER B)113 . Worn rin...
Preview 2 out of 10 pages
Add to cart1. How is efficiency found? A) output over input B) input over output C) output times input times 100 D) output times input divided by hp - ANSWER A) Output over input 2. What is the maximum capacity in kg of a heavy duty ladder? A) 136 B) 113 C) 102 D) 91 - ANSWER B)113 . Worn rin...
A ______ conveys a liquid. - ANSWER Pump What are the two main categories of pumps? - ANSWER Centrifugal and positive displacement Pumps at a constant capacity regardless of pressure. - ANSWER Positive displacement Which pump does not see a decrease in flow with an increase in viscosity? - ...
Preview 1 out of 1 pages
Add to cartA ______ conveys a liquid. - ANSWER Pump What are the two main categories of pumps? - ANSWER Centrifugal and positive displacement Pumps at a constant capacity regardless of pressure. - ANSWER Positive displacement Which pump does not see a decrease in flow with an increase in viscosity? - ...
Auxiliary View - ANSWER view where a slanted surface is projected to a plane that is parrallel to the surface perspective, oblique, isometric - ANSWER 3 types of sketches Oblique - ANSWER Front face is of an object is drawn the same way as the front view of an orthographic Oblique - ANSWER ...
Preview 1 out of 1 pages
Add to cartAuxiliary View - ANSWER view where a slanted surface is projected to a plane that is parrallel to the surface perspective, oblique, isometric - ANSWER 3 types of sketches Oblique - ANSWER Front face is of an object is drawn the same way as the front view of an orthographic Oblique - ANSWER ...
Millwright Level 2 – Bearings Correct 100% What are the principle parts of a friction bearing housing? - ANSWER Base, Base bolt slots, cap and cap bolt holes. What are friction bearing housings made from adn what factors influence the choice of housing? - ANSWER Cast Iron, Cast Steel, Fabr...
Preview 2 out of 7 pages
Add to cartMillwright Level 2 – Bearings Correct 100% What are the principle parts of a friction bearing housing? - ANSWER Base, Base bolt slots, cap and cap bolt holes. What are friction bearing housings made from adn what factors influence the choice of housing? - ANSWER Cast Iron, Cast Steel, Fabr...
1. What type of oil or grease would be used in a heavy load situation? a. Synthetic oil b. Extreme pressure lubricant c. Mineral oil d. Any hydraulic fluid - ANSWER b. Extreme pressure lubricant 2. The most common measurement of kinematic viscosity is what? a. Viscosity b. Centistok...
Preview 1 out of 4 pages
Add to cart1. What type of oil or grease would be used in a heavy load situation? a. Synthetic oil b. Extreme pressure lubricant c. Mineral oil d. Any hydraulic fluid - ANSWER b. Extreme pressure lubricant 2. The most common measurement of kinematic viscosity is what? a. Viscosity b. Centistok...
Most installation procedures start at the machine foundation substructure because? a. the manual says so b. the foundation introduces misalignments in the equipment c. the foundation moves d. the foundation is inconsistant - ANSWER b. the foundation introduces misalignments in the equipment W...
Preview 1 out of 3 pages
Add to cartMost installation procedures start at the machine foundation substructure because? a. the manual says so b. the foundation introduces misalignments in the equipment c. the foundation moves d. the foundation is inconsistant - ANSWER b. the foundation introduces misalignments in the equipment W...
Two kinds of flat bearings differ from there housings they are A. Solid end of friction B. Tight and tapered C. Scored and roller D. Solid and split - ANSWER D. Solid and split **The choice of bearing tens of the load rotational speed direction of Pull and support design solid bearings and sp...
Preview 3 out of 23 pages
Add to cartTwo kinds of flat bearings differ from there housings they are A. Solid end of friction B. Tight and tapered C. Scored and roller D. Solid and split - ANSWER D. Solid and split **The choice of bearing tens of the load rotational speed direction of Pull and support design solid bearings and sp...
Demulsibility is the ability of oil to a. absorb into another substance b. absorb into water c. separate from water d. maintain visibility - ANSWER c. seperate from water When oxidation of oil takes place a. oil is formed b. sludge is formed c. pour point is dropped d. slurry is formed -...
Preview 1 out of 2 pages
Add to cartDemulsibility is the ability of oil to a. absorb into another substance b. absorb into water c. separate from water d. maintain visibility - ANSWER c. seperate from water When oxidation of oil takes place a. oil is formed b. sludge is formed c. pour point is dropped d. slurry is formed -...
What is pressure defined as? - ANSWER Force per unit area F=(P)(A) What is the pressure of the Earth's atmosphere at sea level? - ANSWER 14.7 psi How is power defined? A. The rate or velocity at which power is done B. The rate or velocity at which work is created C. The speed of the veloci...
Preview 2 out of 8 pages
Add to cartWhat is pressure defined as? - ANSWER Force per unit area F=(P)(A) What is the pressure of the Earth's atmosphere at sea level? - ANSWER 14.7 psi How is power defined? A. The rate or velocity at which power is done B. The rate or velocity at which work is created C. The speed of the veloci...
saddle - ANSWER the safe working load of a rigging hook is accurate only when the load is suspended from the ______________ of the hook 15 - ANSWER OSHA requires that a hook be replaced if the throat has opened _____ percent or more from it's original size. 40 - ANSWER A hook that is point lo...
Preview 1 out of 4 pages
Add to cartsaddle - ANSWER the safe working load of a rigging hook is accurate only when the load is suspended from the ______________ of the hook 15 - ANSWER OSHA requires that a hook be replaced if the throat has opened _____ percent or more from it's original size. 40 - ANSWER A hook that is point lo...
What are the 2 main categories of screw compressor - ANSWER Oil wet and oil free dry screw comp Witch rotor is the driver on a screw compressor - ANSWER The male rotor What determines the capacity of a screw compressor - ANSWER Rotor length, diameter, lobe flute design and speed What determ...
Preview 2 out of 6 pages
Add to cartWhat are the 2 main categories of screw compressor - ANSWER Oil wet and oil free dry screw comp Witch rotor is the driver on a screw compressor - ANSWER The male rotor What determines the capacity of a screw compressor - ANSWER Rotor length, diameter, lobe flute design and speed What determ...
Centrifugal pumps - ANSWER Centrifugal pumps are a type of machine used to transport fluids by the conversion of rotational kinetic energy to the hydrodynamic energy. operating principles - ANSWER Centrifugal pumps operate using kinetic energy to move fluids, utilizing an impeller and and a circu...
Preview 1 out of 1 pages
Add to cartCentrifugal pumps - ANSWER Centrifugal pumps are a type of machine used to transport fluids by the conversion of rotational kinetic energy to the hydrodynamic energy. operating principles - ANSWER Centrifugal pumps operate using kinetic energy to move fluids, utilizing an impeller and and a circu...
What controls the servo valve in a hydraulic governor - ANSWER Electrical controller What is the purpose of a sleeve - ANSWER To reduce shaft wear Why are gate valves used on pump inlet and outlets - ANSWER For isolation What does misaligned bearing bores cause - ANSWER Bent shaft an instru...
Preview 1 out of 4 pages
Add to cartWhat controls the servo valve in a hydraulic governor - ANSWER Electrical controller What is the purpose of a sleeve - ANSWER To reduce shaft wear Why are gate valves used on pump inlet and outlets - ANSWER For isolation What does misaligned bearing bores cause - ANSWER Bent shaft an instru...
1. Metallic packing is used in a stuffing box due to: a. The need for a good seal b. In a high temperature application c. Compatibility with acids d. Good swelling properties allow expansion for better sealing - ANSWER b. In a high temperature application 2. Why is a lapping plate softer th...
Preview 2 out of 12 pages
Add to cart1. Metallic packing is used in a stuffing box due to: a. The need for a good seal b. In a high temperature application c. Compatibility with acids d. Good swelling properties allow expansion for better sealing - ANSWER b. In a high temperature application 2. Why is a lapping plate softer th...
Most installation procedures start at the machine foundation substructure because? a. the manual says so b. the foundation introduces misalignments in the equipment c. the foundation moves d. the foundation is inconsistant - ANSWER b. the foundation introduces misalignments in the equipment W...
Preview 1 out of 3 pages
Add to cartMost installation procedures start at the machine foundation substructure because? a. the manual says so b. the foundation introduces misalignments in the equipment c. the foundation moves d. the foundation is inconsistant - ANSWER b. the foundation introduces misalignments in the equipment W...
Entire belt runs off at all points of the line - ANSWER Belt is strained or elongated excessively on one side If belt is new allow time break in, if it is not new or does not break in properly cut out strained section and splice in new section The belt looks hard and has excessive cracks what ...
Preview 2 out of 5 pages
Add to cartEntire belt runs off at all points of the line - ANSWER Belt is strained or elongated excessively on one side If belt is new allow time break in, if it is not new or does not break in properly cut out strained section and splice in new section The belt looks hard and has excessive cracks what ...
Area of Triange - ANSWER A=1/2bh Area of a circle - ANSWER A=πr² Volume of a rectangular solid - ANSWER V=lwh Volume of a cylinder - ANSWER V=πr²h Volume of a sphere - ANSWER V=4/3πr³ Volume of a pyramid - ANSWER V=1/3Bh Volume of a cone - ANSWER V=1/3πr²h Circumference ...
Preview 1 out of 2 pages
Add to cartArea of Triange - ANSWER A=1/2bh Area of a circle - ANSWER A=πr² Volume of a rectangular solid - ANSWER V=lwh Volume of a cylinder - ANSWER V=πr²h Volume of a sphere - ANSWER V=4/3πr³ Volume of a pyramid - ANSWER V=1/3Bh Volume of a cone - ANSWER V=1/3πr²h Circumference ...
Preventive maintenance - ANSWER is the periodic inspection and maintenance of plant assets and equipment to uncover conditions that may to equipment failure or shortened life This measures the amount of contaminants per litre of fluid. a. ferromagnetic analysis b. total base number c. infrared...
Preview 2 out of 8 pages
Add to cartPreventive maintenance - ANSWER is the periodic inspection and maintenance of plant assets and equipment to uncover conditions that may to equipment failure or shortened life This measures the amount of contaminants per litre of fluid. a. ferromagnetic analysis b. total base number c. infrared...
Stuvia customers have reviewed more than 700,000 summaries. This how you know that you are buying the best documents.
You can quickly pay through credit card or Stuvia-credit for the summaries. There is no membership needed.
Your fellow students write the study notes themselves, which is why the documents are always reliable and up-to-date. This ensures you quickly get to the core!
You get a PDF, available immediately after your purchase. The purchased document is accessible anytime, anywhere and indefinitely through your profile.
Our satisfaction guarantee ensures that you always find a study document that suits you well. You fill out a form, and our customer service team takes care of the rest.
Stuvia is a marketplace, so you are not buying this document from us, but from seller suedocs. Stuvia facilitates payment to the seller.
No, you only buy these notes for $39.99. You're not tied to anything after your purchase.
4.6 stars on Google & Trustpilot (+1000 reviews)
67096 documents were sold in the last 30 days
Founded in 2010, the go-to place to buy study notes for 14 years now