Relief cut - Study guides, Class notes & Summaries

Z-51 Written Exam Questions and Complete Solutions In a steam turbine, what is the function of a Kingsbury thrust bearing? A) Maintain first stage steam pressure. B) Compensate for coupling misalignment. C) Adjust shaft torque at start up. D) Maintain axial positioning of the rotor shaft. - Answer: D) Maintain axial positioning of the rotor shaft. The ratio of actual pressure of water pressure in the atmosphere to the saturated pressure of given temperature is A) partial pressure....

G2 Gas Technician Exam (2024/ 2025 Update) Questions and Verified Answers| 100% Correct| Grade A Q: Installation of a propane tank under 1000 USWG what would be the minimum distance from a regulator to a building opening? Answer: 3' Q: If an appliance is less than 85% efficient and non positive it would be considered a? Answer: Category 2. Q: For a steam boiler what would be the most important safety control? Answer: Low water cut off. Q: For a low pressure s...

CWB Welding Inspector Level 1 Exam (Latest 2024 / 2025 Update) Questions and Verified Answers | 100% Correct | Grade A Q: From the welding problems identified below which one of the five does not fit the pattern established by the other four? a) Insufficient throat. b) Incorrect bevel angle. c) Loss of shielding gas. d) Improper fit up. e) Use of wrong consumable. Answer: a) Insufficient throat. Q: A 10 mm fillet weld has a nominal: a) Throat dimension of 10 mm. b) Area of 10 sq. mm. c) Leg size...

What gas is released from a fire? a. helium b. hydrogen c. carbon dioxide d. carbon monoxide Correct Answer-d. carbon monoxide After an outbreak of food-borne illness in the cafeteria, you discover one of your employees has an infected cut on his finger. You should: a. call the state public health office to investigate b. have the lab culture the kitchen c. fire the employee d. send the employee home until the cut has healed Correct Answer-d. send the employee home until the cut h...

NCCER 26208-17 Questions and Answers Already Graded A To properly install heat-shrink insulators, _____. Slip the insulator over the connector and apply heat for a few seconds When used in control cable, which of the following must be grounded in order to be effective? Drain wires To determine the correct connector size for MC cable, _____. Refer to the manufacturer literature Burnishes, nicks, and scrapes are generally the result of which of the following? Poorly stripped conductors When st...

Mechanics Exam Questions and Answers Already Passed ** An MOV burns out, you replace it but cannot read voltage or resistance. What should you do? Replace it with a larger one (630) * On a Ward-Leonard circuit, the brake is set but the motor is trying to slip through the brake. What circuit is the issue? Suicide circuit (425) ** A Hydro runs up with no load but does not run up with a full load. What is the issue? The relief valve is set too low (805) ** Runby for a 1:1 car hits t...

Which valves are located between the boiler and the feedwater pump? - Feedwater Stop Valve and Feedwater Check Valve What is the function of the Check Valve? - To prevent the boiler pressure from forcing the boiler water back into a feedwater tank or deaerator when the pump shuts off. (Allows flow in only one direction) The 4 safety features required on a steam boiler is: - Safety Relief Valve, Blow Down Valve, Low Water Cut-off, Pressure Gauge Safety Relief Valves should be set by a: - Q...

FTCE ART K-12 Revision 3 - Art History and Culture Exam Combined Tested Questions With Revised Correct Detailed Answers |ALREADY GRADED A+ PASS 2024 >> BRAND NEW VERSION!! 1) Acceptance of fiber arts as a medium - ANSWER work, sewing, embroidery, knitting and crocheting. Textile, fiber 1900 - embroidery was the medium for feminine protest 1950 Judy Chicago "The Dinner Party" celebrates 39 women from history and sets a place at the table in a long triangle. Tra...

Special Engineers Exam Questions with Answers Latest 2024/2025 (100% Solved) boilers operating at a steam or other vapor pressure of 15 psig. or less or a hot water or other liquid boiler in which the pressure does not exceed160 psig or a temperature of 250 degrees F. - ANSWER what is meant by the term low pressure boiler? high and low pressure boilers not to exceeda total of 50 boiler horsepower, or a shift engineer in a 100 horsepower plant. - ANSWER a person holding a current state of M...

1/2" - ANSWER-Sight Glass Minimum Connection 3/4" - ANSWER-Low Water Cut-off Draw Minimum Connection 1" - ANSWER-Water Column Minimum Connection 3/4" - ANSWER-Control Manifold Minimum Connection 1/4" - ANSWER-Sight Glass Drain Minimum Connection 1" - ANSWER-Bottom Blow-Off Minimum Connection 2 1/2" - ANSWER-Bottom Blow-Off Maximum Connection 2 1/2" - ANSWER-Surface Blow-Down Maximum Connection 3" - ANSWER-Threaded Safety Valve Maximum Connection 4 1/2" - ANSW...