Pipe pe Study guides, Class notes & Summaries

The Plumbing Inspection: AHIT Questions with Accurate Answers 2024 Which of the following does NOT have to be inspected during the plumbing inspection? A. fire and lawn sprinkler systems B. fixtures and faucets C. water heating equipment D. supply and drain, waste, and vent (DWV) piping A. fire and lawn sprinkler systems Which action IS required by most standards of practice during the plumbing inspection? A. required to operate automatic safety controls B. required to observe...

Final Water distribution level 3 study guide Exam Q&A A factor or value used to indicate the smoothness of the interior of a pipe - CORRECT ANSWER-Cfactor Major parts of water distribution - CORRECT ANSWER-Pipes, storage facilities, pumping stations, valves ,fire hydrants, meters, and other appurtenances Main purpose of water storage facilities - CORRECT ANSWER-To provide sufficient amount of water to average or equalize the daily demands on the water supply system Types of storage f...

NCCER PLUMBING LEVEL 1 REAL EXAM 200 QUESTIONS AND CORRECT ANSWERS 2024 UPDATE ALREADY GRADED A+. vertical and horizontal piping along with sizes and a riser number that refers back to the full set of plumbing drawings are shown on Riser diagrams Drawings that can be used to determine such factors as overall dimensions, actual inside dimensions, fitting depth, and laying length of the fittings are known as Catalog drawings Drawings of products that provide enough detail to show how...

For most communities, how far should a private well be located from a septic system? a. 18' to 20' b. 30' to 40' c. 50' to 70' d. 75' - 100' - ANSWER D What is a symptom of a water logged pressure tank? a. The pressure gauge doesn't work b. The pump runs constantly c. The pump vibrates too much d. The tank returns to the high limit too fast - ANSWER B If, during a test of the well equipment, the pressure comes up over the preset high limit, what might be the problem? a. T...

NGA 31 & 40 - Installing PE/Steel Pipes (31A), Installing Pipe in an excavation (31B) Horizontal Boring (31D), Dead Insertion (31E), Replacing Tracer Wire (40) *BASIC 8 OQs* Original Set [Notes based on the NGA 31/40 Student Manual written by Industrial Training Services] Backfill Refilling an excavated area or trench with excavated material. Proper backfill material depends on soil conditions and piping use. Bore Hole A hole bored into the ground vertically or horizontally to form a na...

CETP 4.1 Designing & Installing Exterior Vapor Distribution Systems Already Passed _____________ is the sum of the rated btu/hr input for each propane appliance connected to the vapor distribution system. Total gas demand Where do you record the ratings of the btu/hr input for a customers current appliances? Customer gas appliance use profile form _____________ is used to determine the amount of propane required to operate appliances at a reduced demand, and assumes full cycle happen typicall...

30 TAC Chapter 285 - This chapter establishes minimum standards for planning materials, construction, installation, alteration, repair, extension, operation, maintenance, permitting, and inspection of OSSFs. This chapter also provides the procedures for the designation of local governmental entities as authorized agents. 30 TAC Chapter 30 - The licensing of installers, designated representatives, and site evaluators and the registration of apprentices is included in this chapter. Title 5, ...

FLETC Written Exam 4 With Verified Answers Latest Updated 2024/2025 / Graded A+. Three Types of Explosions - ANSWER Mechanical Chemical Nuclear High Explosive - ANSWER Explosive which normally requires a blasting cap for initiation and once initiated produces a supersonic detonation with a shattering or brisant effect Detonate without confinement, doesn't need container Low Explosive - ANSWER Explosive, which when unconfined, responds to initiation by deflagration or burning and produces...

A factor or value used to indicate the smoothness of the interior of a pipe - ANSWER Cfactor Major parts of water distribution - ANSWER Pipes, storage facilities, pumping stations, valves ,fire hydrants, meters, and other appurtenances Main purpose of water storage facilities - ANSWER To provide sufficient amount of water to average or equalize the daily demands on the water supply system Types of storage facilities - ANSWER Clear wells, elevated tanks,standpipes,ground level storage ta...

Fluid Mechanics correct answer: study of forces on liquids and gases which are at rest (statics) or in motion (dynamics) Viscosity correct answer: a measure of a fluid's resistance to flow Reynolds Number (Re) correct answer: The ratio of inertial forces to viscous forces Kinematic Viscosity correct answer: ratio of dynamic viscosity to density Stokes (St) correct answer: physical unit for kinematic viscosity, named after George Gabriel Stokes, where 1 St = 10-4 m2/s Poise (...