Voltmeter multiplier - Study guides, Class notes & Summaries

(a) A die can be used to make a taper thread on the outside of a piece of conduit T/F Safety True (a)The lowest range of current in which painful shock is felt normally a) 1mA b)1-8mA c)8-15mA d)15-20MA e)20-75MA Safety C) 8-15 ma- painful shock control not lost Brainpower Read More 0:12 / 0:15 (a)the best way to rescue a person who is in contact with a 480 V electrical circuit is Safety use a loose dry clothing to pull them away (a)Your notes divide machi...

CET Exam 236 Questions with Verified Answers When did the first CET certification program begin? - CORRECT ANSWER 1965 When did ETA initiate certification maintenance? - CORRECT ANSWER 1996 All ETA Certification categories require the passage of the Associate CET examination. True or false. - CORRECT ANSWER False. To qualify for MASTER CET, the examinee must attain a score of 85% on each separate exam. True or false. - CORRECT ANSWER False An associate CET cannot attempt one of ...

ACET study guide Exam 174 Questions with Verified Answers Binary is in vaules of? - CORRECT ANSWER 1 , 2, 4, 8...... so on incressed by *2 each following Octal place vaules? - CORRECT ANSWER 0-7 each digit holds a place vaule of 3 binargy digits Hex - CORRECT ANSWER 0-9 followed by A-F. A=10 each digit holds 4 in binary Binary divide by rule - CORRECT ANSWER When you divide, no remainder =0, remainder =1 Don't carry foward the remainder. Revese the reminders when translating to ...

CET Associate Certified Electronics Technician CIE book 93 Questions with Verified Answers Three Colors for a 10 ohm resistor - CORRECT ANSWER Brown Black Brown Three Colors for 4.7 ohm resistor - CORRECT ANSWER Yellow Violet Gold Two Terminal current control circuit device - CORRECT ANSWER rheostat 12 Volt battery across red red red resistor, mW dissipated by resistor - CORRECT ANSWER .65.5 mW Resistance Equivalency formula - CORRECT ANSWER R1 x R2/R1+R2 The larger the capacit...

ETA CET Exam 382 Questions with Verified Answers The resistance of a component at a given frequency - CORRECT ANSWER What is impedance? Diode - CORRECT ANSWER A two terminal device that conducts in only one direction. Printed Circuit Board - CORRECT ANSWER Insulating board containing conductive tracks for circuit connections. Capacitor - CORRECT ANSWER An electrical device used to store electrical charge. 1996 - CORRECT ANSWER When did the ETA initiate renewal? False - CORRECT ...

ASVAB Electronics Exam 159 Questions with Verified Answers Electricity - CORRECT ANSWER General term for the variety of phenomena resulting from the presence and flow of electric current Volts Amperes (amps) Ohms - CORRECT ANSWER 3 ways Electricity is measured Volts - CORRECT ANSWER Measure the difference of potential between 2 points Amperes (amps) - CORRECT ANSWER Measure the number of electrons that move past a specific point in 1 second (i.e. electrical currents) Ohms - CO...

NCCER Practice test Multiple Choice Questions Answered 2024 Why can't a lead acid battery be an explosive hazard? A. Acid is explosive B. Hydrogen gas is produced during charge and discharge C. Pcb's in batteries are explosive D. Batteries are constructed of flammable material - B. Hydrogen gas is produced during charge and discharge When a megger is used to check electrical equipment before initial energizing, the electrician will ensure that the phase conductors are free ...

HVAC final exam, unit 15 already graded A+ A control can be which of the following? ️All of the above An example of a power consuming device would be a(n) ____ while an example of a non-power consuming device would be a(n) _____. ️Light bulb, single-pole single-throw switch An electrical power consuming component. ️is also known as a load The line side of a switch is the. ️side the power source is connected to If an air conditioning system is calling for cooling and the compr...

CET Study Guide Exam 294 Questions with Verified Answers B+, or supply voltages in electronics products, is considered to be: A. +5 to +12 VDC B. 0 to 30 V DC C. +12 to 300 V DC D. The anode or plate voltage supply - CORRECT ANSWER A: +5 to +12 VDC Leakage current in an electronic product, between either of the AC power cord conductors and the chassis or any exposed metal parts should not exceed A. 5 micoamps B. 500 microamps C. 5 milliamps D. 50 milliamps - CORRECT ANSWER D: 50...

The Associate CET Study Guide Exam 276 Questions with Verified Answers B+, or supply voltages in electronics products, is considered to be: A. +5 to +12 VDC B. 0 to 30 V DC C. +12 to 300 V DC D. The anode or plate voltage supply - CORRECT ANSWER D. The anode or plate voltage supply Leakage current in an electronic product, between either of the AC power cord conductors and the chassis or any exposed metals should not exceed _________. A. 5 microamps B. 500 microamps C. 5 millia...