Loose screws - Study guides, Class notes & Summaries

Brake Pad Minimum Thickness Customer Pay Warranty CPO → Customer Pay: 3mm → Warranty: 4mm (3.9mm) → CPO: 5 mm Brake bleed pressure setting (bar): → 2 bar max - Location of MSDS: → Online CPO test drive (length and distance): → 20 uninterrupted minutes/ 5 continuous miles Caliper bleeding with 2 bleed screws → Outer bleeder first, then inner - Is prescription eye wear valid eye protection in a bmw shop? → no How do you measure a vehicle wheel base? 1 | P a g e | ...

Industrial Maintenance and Mechatronics CH-4-5 Tools and Fasteners 100% Correct SAE Society of Automotive Engineers metric system The decimal measuring system based on the meter, liter, and gram as units of length, capacity, and weight or mass. wrenches used to tighten or loosen nuts and bolts. Sockets used to tighten or loosen nuts and bolts, comes in various size and a ratcheting handle. ratchet A device consisting of a bar or wheel with a set of angled teeth in which a pawl...

When should the home inspector not remove the cover (dead-front) to the main panel? if the inspector gets a shock upon touching it if the inspector's customer is present if the meter is inside the building if there are multiple panels - Answer If the inspector gets a shock upon touching it What is a subpanel? a panel housing the main disconnect for the service a panel that adds more circuits to the service a panel that adds more power to the service a second main panel in ...

RAC 40 Quiz 6 Review - Questions and Answers When connecting stranded wire under a screw terminal (like a thermostat) what process should be used to ensure a secure and solid connection is obtained? Solder the end of the wire so all copper strands are binded together and no loose wires will fall out Nails are sometimes coated with zinc to protect them from corrosion True A wall anchor is a onetime fastener False A pin rivet must be installed in a properly sized, pre-drilled hole. True Perforat...

RAC 40 Quiz 6 Review Practice Test 2024. When connecting stranded wire under a screw terminal (like a thermostat) what process should be used to ensure a secure and solid connection is obtained? - CORRECT ANSWER Solder the end of the wire so all copper strands are binded together and no loose wires will fall out Nails are sometimes coated with zinc to protect them from corrosion - CORRECT ANSWER True A wall anchor is a one time fastener - CORRECT ANSWER False A pin rivet must be in...

What should be done with all washers and screw with lock washer assemblies? Replace the washers and screws What should be done with steel bearing if the sealing surface is worn? Can be reverse when installed How can over sized bearing bores be determined? If at time of assembly & interference of press if condition is not gain How should over sized bearing bones be determined? Replace Housing What should be done to the housing if a ridge can be felt across the co...

vehicle inspection: - Answer your responsibility to check the ambulance usually at the beginning of shift and after each shift. use checklist as you approach an ambulance, check: - Answer to see if it is leaning to one side (indicates low tire, broken spring, suspension problem) also look for: - Answer leaks or outside damage/wear, check tire pressure/gauge and tread depth, check for loose/missing nuts and screws, make sure windshield/wipers are clean, check mirrors and outside co...

Step 1 (set up) Make sure that main valves are off and the regulator pressure adjusting screws are backed out with no pressure readings on the gauges. Step 2 (set up) Ensure torch valves are off. Previous Play Next Rewind 10 seconds Move forward 10 seconds Unmute 0:02 / 0:15 Full screen Brainpower Read More Step 3 (set up) Stand to the side and s-l-o-w-l-y turn on the oxygen cylinder valve. Do not face the regulator while you do this. Once pressure reads on the gauge o...

A pneumatic winch used to move heavy objects is a(n)______. - Tugger A device used to join several piping or tubing runs is a(n)_______ . - Manifold, When inspecting a completed cut made with oxyfuel cutting equipment, the drag lines of the cut should be n e a r_____ and not very pronounced. - vertical A ( n )_______is a sharp, ragged edge of metal. - Burr A boilermaker working at extreme heights must follow safety precautions not only to prevent falls but also to prevent causing ______...

The Exterior Inspection: AHIT Questions 2024 Which of the following is NOT included in a standard home inspection? A. screens, awnings, and shutters B. wall framing, if visible C. chimney D. roof drainage system A. screens, awnings, and shutters Which of the following IS included in a typical site inspection? A. swimming pools B. docks C. awnings D. retaining walls D. retaining walls When should a retaining wall be inspected? A. every retaining wall should be insp...